10. Aline shaft is to transmit 30 kW at 160 r.p.m. It is driven by a motor placed directly under it by means of a belt running on alm diameter pulley keyed to the end of the shaft. The tension in the tight side of the belt is 2.5 times that in the slack side and the centre of the pulley over-hangs 150 mm beyond the centre line of the end bearing. Determine the diameter of the shaft, if the allowable shear stress is 56 MPa and the pulley weighs 1600 N. JAns. 60 mm

10. Aline shaft is to transmit 30 kW at 160 r.p.m. It is driven by a motor placed directly under it by means of a belt running on alm diameter pulley keyed to the end of the shaft. The tension in the tight side of the belt is 2.5 times that in the slack side and the centre of the pulley over-hangs 150 mm beyond the centre line of the end bearing. Determine the diameter of the shaft, if the allowable shear stress is 56 MPa and the pulley weighs 1600 N. JAns. 60 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A compound shaft drives several pulleys, as shown. Segments (1) and (2) of the compound shaft are hollow aluminum (G = 4000 ksi) shafts that have a polar moment of inertia of J = 2.835 in4. Segments (3) and (4) are solid steel (G = 12000 ksi) shafts that have polar moment inertia of J = 1.024 in4. The bearings shown allow the shaft to turn freely. Assume TB = 980 lb.ft TD= 525 lb.ft TE = 130lb.ft L1 =74in L2 =29in L3 =34in L4 =35in. Calculate the rotation angle (including the correct sign) of pulley E with respect to point A.
None
Figure 1 is presented the solid shaft AB rotates at 650 rpm and transmits 30 kW from the motor machine tools connected to gears F and G. Assuming that, 10 kW is taken off at gear F and 20 k taken off at gear G, knowing that allowable torsional shear stress is equal to (65 plus last digit of student ID) MPa. Design the smallest permissible diameter of shaft AB. Figure 1 150 mm 225 mm 905 mm 150 mm 60 mm 100 mm D. 60 mm B.
QUESTION 20 A compound shaft consists of a solid rod of diameter D and a sleeve of diameter 2D of the same material firmly fixed together by a key. The compound shaft is subjected to a torque of 100 kNm. Key Bushing Shaft Oa. The torque carried by the rod and the sleeve are 50 kNm each. Ob. The torque carried by the rod and the sleeve are 100 kNm each. Oc. The entire torque of 100 kNm is carried by the outer sleeve only. O d. None of the above answers.
1. The endurance limit for rotating shaft, if its ultimate strength Su=1600 Mpa is:
Determine the diameter of a solid shaft in mm to be used for a 373-kW, 250 rpm application if the allowable torsional deflection is 1 deg in a length of 18-diameters and the allowable stress is 70 MPa. Use modulus of rigidity of 90 GPa.
Design a rigid flange coupling to transmit a torque of 228N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa > Provide FBD
A hollow steel shaft is stressed to 35 MPa by a torque of 200000Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter both in mm.
Compute for the induced compressive stress in kPa, of a steel shafting of 59 mm diameter and 954 m in length that issubjected to an increase of temperature of 88ºC. Use 6.5x10-6/F, E = 30x106 psi.
Consider two steel shafts CFG and HJ of diameters 50 mm and 70 mm respectively as shown in fig. The shaft CFG is supported at two bearings, while shaft HJ is fixed at 'H' and supported by bearings at 'J. Determine the torques T 1 and T 2 if the twisting at gears C and G is required to be 0.05 rad. Take E=205GPA, G=70GPA 600 mm 75mm 600 mm 50mm 800mm G. T2
The disc clutch of an automobile is carried on a 2-inch 6-splined shaft and not to slide under load. The nominal dimensions are as follows: b = 0.25 D; t = 0.075 D and d = 0.85 D. The hub length of 150 % of shaft diameter. Determine the total horsepower transmitted at 3,600 rpm, if the yield strength of the shaft is 1,400 psi
A composite shaft is comprised of an inner solid steel shaft 1/6 ft in diameter slipped over with a hollow bronze shaft of 1/4 ft outer dimater and 1/6 ft inner diameter and of the same length as the steel shaft. The two shafts are then fastened rigidly together at their ends. For steel, G = 12 × 106 psi, and for bronze, G = 6 × 106 psi. What torque can be applied to the composite shaft without exceeding a shearing stress of 12,000 psi in the steel or 8,000 psi in the bronze?