10. A superheat steam Rankine cycle has turbine inlet condition of 9.1 bar and expand in a turbine to 1.0 bar. What is the pump work in HP if the efficiency of the pump is 85%? The mass of steam is constant at 1200 kg/min. a.) 342 HP b.) 296 HP c.) 254 HP d.) 384 HP

10. A superheat steam Rankine cycle has turbine inlet condition of 9.1 bar and expand in a turbine to 1.0 bar. What is the pump work in HP if the efficiency of the pump is 85%? The mass of steam is constant at 1200 kg/min. a.) 342 HP b.) 296 HP c.) 254 HP d.) 384 HP

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

HW2: A hydroelectric power plant built for a design head of Hn=12.5 m should develop a rated output of 12000 hp. Assuming e=0.90 determine: a) the discharge be utilized b) how many turbines are needed if francis types turbines with ns-450 at N= 180 rpm are used.
Please choose the right answer for each question as below: a): Which of the following is a path function 1-Energy 2-Entropy 3-Exergy 4-None of the above b): Moisture content of steam at the turbine exit in the power plant can be reduced by 1-Superheating of steam 2-Reheating in turbine 3-Increasing the condenser pressure 4-Through all of above methods c) The irreversibility occurs during a thermodynamic process can also be named as 1- Work produced 2- Energy change 3- Exergy destroyed 4- Exergy loss d): If the ideal vapour compression refrigeration cycle operates in a reversible mode then the process of throttling will be 1-an isentropic process 2-an isothermal process 3-an isenthalpic process 4-adiabatic process
A garden hose with an inside diameter of 2 cm carries water with a mass flow rate of 60 liters per minute at 20°C with an enthalpy of 83 kJ/kg. Pression is 78KPa. The outlet of the hose has a tube that changes its diameter. a) What will be the outlet diameter to achieve a speed of 1 m/s b) What is the enthalpy change of the fluid?
In an ideal Ericsson cycle with a regenerator the pressure ratio is 2.5. The pre-compression pressure is 0.5 Mpa, and the maximum and minimum volumes are 0.02 m ^ 3 and 0.005 m ^ 3, respectively. Since there is 0.06 kg of air in the cycle: a) pre-compression volumeb) compression end pressurec) minimum temperatured) Find the efficiency of the cycle. R = 0.287 kj / kh.K
A: Derive the steady flow energy equation and reduce it for a. A turbine (Reversible Process) b. A pump (Reversible Process) c. A nozzle (Reversible Process) d. A throttling (Irreversible Process)
Answer letters D, E, F
The air entering a compressor with a pressure ratio of 10 at 100kPa at 27°C leaves at 600K. It enters the turbine at a temperature of 1300 K and exits at a temperature of 800 K. Since the power of the gas turbine is 10 MW, b) Find the amount of fluid circulating in the installation. c) Find the adiabatic efficiencies of the gas turbine and the compressor. d) Find net work Note. Assume that the specific heat of heating of the air is constant. cp=1 kj/kgC cv=07181 kj/kgC
You have invented a hydrogen‐fueled turbine engine that operates between a combustion temperature of 2500. K and an exhaust manifold temperature of 500. K. How much work does it produce per kilojoule of fuel energy if it operates at 75% of maximum theoretical efficiency?
5. A boiler produces 5000kPa steam which is 67% dry, from boiler feed water flow rate is 960 kg/min, a) Find the heat rate in kJ/hr. 100°C. If the mass b) What is the equivalent evaporation? c) What is the factor of evaporation? d) What is the boiler efficiency if the fuel has a calorific value of 35MJ/kg, and its consumption is 3.5tonnes/hr.?
Q.4/A combination of a heat engine driving a heat pump, the heat energy supplied to the heat engine is 5040 J, and the temperature of the hot reservoir Tmin is 30 °C and the thermal efficiency of the heat engine is 41%. The work energy W12 of heat engine goes to the heat pump that the coefficient of performance COPHP=1.3. Find: a) The Tmaxmax of the heat engine, b) The Tminmin of the heat pump, c) The work done between two engines d) Qrej of the heat pump T max 150 °C Qadd = 5040 J. W 12 Н.Е. Н.Р. Qrej 30 °C T min
3. A rear mounted air-cooled SI engine has 6 cylinders, 3.375 in x 2.6 in bore and stroke respectively, acompression ratio of 8 and developed 80 BHP at 4400 rpm. It was noted that brake thermal efficiency is26 %, volumetric efficiency is 74 % and mechanical efficiency is 71 %. For the ideal cycle, conditions atthe start of compression are 14.7 psia, 140 o F.Calculate a) Percent clearance, b) P, T at the end of compression, c) Brake engine efficiency, d) massflow rate of air, e) torque (lb-ft), f) AF with Q hv = 19100 BTU/lb fuel
None