10. A sphere hanging freely from a cord is in a) stable equilibrium. b) unstable equilibrium. c) neutral equilibrium. d) positive equilibrium. e) negative equilibrium.

Q: 2. A cube with a length of 10cm is made up of Aluminum metal (S = 25x10⁹ Pa). A horizontal shear…

A:

Q: Bones, on the whole; do not fracture due to tension or compression. Rather they generally fracture…

A: Option e is correct. Bones fracture due to compression only. Rather they generally fracture due to…

Q: What is the difference between elastic strain and plastic strain?

A:

Q: 8. The block in the given diagram rests on the ground. Which face A, B or Cexperiences a) the…

A:

Q: When using the Method of Sections, if I cut through a member and I assume that the member was in…

A: When using the Method of Sections, if I cut through a member.

Q: A 3 m high embankment is to be constructed as shown in the figure. If the unit weight of soil used…

A:

Q: 10. An aluminum rod is 3.5 m long and 3.25 cm in diameter. A) How much force would be required to…

A:

Q: 6) Multiple choice: What is the AISC recommended slenderness ratio limit for tension members? a)…

A:

Q: Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than o= 67874…

A: Remember that Young's modulus is given by: Y = Stress/Strain Where Stress is given by: Stress =…

Q: What could be the change in length of the wire with a cross sectional area of  0.000025 m2 with…

A:

Q: 3. Consider a load of mass 120.0 kg that is being held up by two tensioned cables. Cable 1, with…

A:

Q: of nm?. Given that P=2 kN; aw the FBD of the rigid membe how the forces at A and B with ct senses.…

A: Given:

Q: 5. A wire made of the same material (Y= 12X100Pa) is cut into two parts, we label it as wire I and…

A: The wire is cut into two pieces.  Piece 1 : Length L1 = L , diameter d1=  d  Piece 2 : length L2 =…

Q: 16 12 Extension (ст) 8 2 4 6 8 Force (N) 2. nh chon al. - indol 3. The scale chosen for the X axis…

A: The scale chosen means smallest division taken in each arm

Q: 40° P3) Add the following 2-D rock stress states, and find the principal stresses and directions of…

A: Detailed explanation: Add the two-dimensional rock stress states that have been provided, as well as…

Q: 1. A piece of 180mm long by 30mm square is in compression under a load of 90kN as shown in the…

A:

Q: A STRAIN, pdf - Adobe Acrobat Reader DC (64-bit) File Edit View Sign Window Help Home Tools STRAIN,…

A:

Q: 1- the phenomenon of necking occurs at yield point.

A: 1. Necking occurs at yield point (statement is true)  as the reduced area gives the neck the largest…

Q: Several studies indicate that the elastic properties of tendons can change in response to exercise.…

A: A) The force constant is the slope of the force versus deformation curve. Determine the force…

Q: A steel wire of diameter 1mm can support a tension if 0.2kN. determine the diameter of a steel cable…

A: Given: The initial diameter of steel wire is D1=1 mm. The initial tension in steel wire is F1=0.2…

Q: Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than o= 99260…

A:

Q: |22 A cable used to elevate heavy materials like steel beams must be tough enough to withstand…

A:

Q: 4. Find P using 1st condition of equilibrium & W2 using 2nd condition of equilibrium P = ? A 1.4 m 2…

A: We have three forces on the rod W1=30 N, P and W2 of length L=3.4 m. W1 and W2 are acting on two…

Q: 7. A vertebra experiences a shearing force, F; = 600N. What is the magnitude of the shear…

A:

Q: 3): Answer the followings (Only Ten)? 1. In Taylor-Orowan dislocation, The amount of force required…

A: In Taylor-Orowan dislocation. The amount of force required to form and move an edge dislocation is…

Q: Describe translational equilibrium and the conditions for this state.

A:

Q: Please don't provide handwritten solution ....

A: First, let us place the x and y-axis in this position. The x-axis is at the base of the figure, and…

Q: 3. The diagram to the left is a beam suspended by wire at one end and a wall on the other. Which…

A: For the FBD of the given support system, we have the prime force of weight of the beam acting…

Q: A compressive force of 6,485 N is applied to a bone that has an outside radius of 2.5 cm and a…

A:

Q: Q4. When a tensile load (F) is applied to a solid homogeneous rod, the rod undergoes a change in…

A: Write the basic expressions related to stress and strain. Here, σ represents the stress, A…

Q: 213. The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before…

A:

Q: 1. Refer to the beam shown in the figure. Given the loading and support condition and assuming that…

A: Given data: wx=wox3L3

Q: The two structural members, one of which is in ten- sion and the other in compression, exert the…

A:

Q: a. ML-1T-2 b. ML2T-2 c. MLT-2 d. MLT-1 e. ML-1T-

A: The process of parallel layers sliding past each other is known as shearing. A pile of papers, a…

Q: The compound bar is composed of brass and copper. It supports the axial loads shown below. Determine…

A: Given: Here are the given data, Brass, d=6.5 inches Copper, d=4.5 inches Fbr=450 lbFco=250 lb To…