1. For a piece of copper wire with length 0.2 m and round cross sectional area with a radius of 1mm, id you applt 100000 N of force to stretch it, the wire will stretch by 5.2 cm. What would happen if you applied the same force but instead you had a piece of copper wire od the same length but the cross sectional area had a radius of 2mm?

Q: Determine the diameter (in mm) of the largest circular hole that can be punched into a sheet of…

A: Have a look

Q: 1.10 Link BD consists of a single bar 1 in. wide and in. thick. Knowing that each pin has a -in.…

A:

Q: A thin rectangular plate is uniformly, deformed, as shown. Determine the shear strain Yxy at P.…

A: Solution: The shear strain of the thin rectangular sheet in the y-direction can be obtained using…

Q: A (2 m)-long steel wire in a musical instrument has a radius of (0.3 mm). When the wire is under a…

A:

Q: 0.5 in. 0.55 in. 1 0.25 in. P PI 3.5 in. A "В B 1.6 in. O C D 0.65 in. 0.75 in. E Knowing that…

A: Given data A vertical force F=380 lbDistance AB=0.65 inDistance BD=0.75 inDistance CE=1.6 inWe are…

Q: A copper wire 4 m. long has diameter of 1 mm, if a load of 10 kg. wt is attached at other end. What…

A: Solution:-Given thatlength of wire (L)=4 mdiameter of wire (d)=1 mm=0.001 mmass of Load (m)=10…

Q: 2. A certain streched wire 120 cm long and 2.4 mm in diameter is fastened to a point in the ceiling.…

A:

Q: When using the Method of Sections, if I cut through a member and I assume that the member was in…

A: When using the Method of Sections, if I cut through a member.

Q: Based on the sign convention we are using, if we cut a beam and draw the left portion of the beam,…

A: Cutting a beam and draw the left portion

Q: 10. An aluminum rod is 3.5 m long and 3.25 cm in diameter. A) How much force would be required to…

A:

Q: Consider a copper wire with cross-sectional area 4 mm?. The Young's modulus for copper is 1.1 × 1011…

A:

Q: Solve the following problems: A mass of 100 kg moves in an acceleration of 10m/sec". Calculate the…

A:

Q: Stiller Düzenleme Üs B 2) A uniform brass plate with area of 18 x 18 m? has mass of 41 kg which is…

A:

Q: What is the area of the stock file if a 1.5 x 10 5kg mass presses down 2.5 feet high stock file that…

A:

Q: What could be the change in length of the wire with a cross sectional area of  0.000025 m2 with…

A:

Q: radius which when stretched by a force of 2 kg. modulus for a wire 2 m long and 0.5 mm in Ex. 1:…

A: To find-(1) Stress(2) Strain(3) Young's modulusGiven-L=2 mr=0.5 mm=5×10-4 mF=mgF=2×9.8N

Q: 1) What is the deformation 8ag in mm? 2) What is the deformation đạc in mm? 3) What is the…

A: Dear Student According to Bartleby guidelines I will only solve 1st question's three subparts. If…

Q: me rigid pipe is supported by a pin at A and an A-36 steel guy wire BD gure Part A 4 ft био μA B…

A: Have a look

Q: A rod stretches 0.02 m when a force of 5000 N is applied to it. How much will it stretch if a force…

A: The 1st option is the answer. 0.006mExplanation:Please see the attached image for the solution.If…

Q: 5. A wire made of the same material (Y= 12X100Pa) is cut into two parts, we label it as wire I and…

A: The wire is cut into two pieces.  Piece 1 : Length L1 = L , diameter d1=  d  Piece 2 : length L2 =…

Q: of aluminum part is 1.2 m and of the C0 part is 2.5 m. Aluminum Copper La 1:f it ie

A: Given data as per question radius of rod = 0.178cm length of copper part = 2.5cm length of aluminum…

Q: Assume a hand has a 1.4m shaft of bone with an average cross-sectional area of 3 [cm] ^2. What is…

A:

Q: A wooden dowel is subjected to a shearing force of 715N on its top cylindrical face. If the dowel…

A: Shearing force F=715 N, diameter of dowel d=3cm (radius r=1.5cm), height of dowel h=11 cm and shear…

Q: A steel bar is 10 mm in diameter and 2 m long. It is stretched with a force of 20 kN. Calculate the…

A: Given data: Diameter (d) = 10 mm = 0.010 m Length = 2 m Force (F) = 20 kN = 20 × 103 N Required: The…

Q: For a constant force, a rope breaks due to stress. Which of the following is useful to reduce the…

A:

Q: Calculate the force a piano tuner applies to stretch a steel piano wire 10.00 mm, if the wire is…

A:

Q: A) by how much does a 55.3kg mountain climber stretch her 0.890 cm diameter nylon r ope when she…

A:

Q: Assume if the shear stress in steel exceeds about 4.00 x10 N/m2 the steel ruptures. (a) Determine…

A:

Q: what is the percentage elongation of an elastic with a cross section of 5 cm2 If the force of 15 N…

A: Given- area of cross-sectional of elastic , A = 5 cm2 = 5 x 10-4 m2 applied force , F =15 N Young's…

Q: A steel wire of diameter 1mm can support a tension if 0.2kN. determine the diameter of a steel cable…

A: Given: The initial diameter of steel wire is D1=1 mm. The initial tension in steel wire is F1=0.2…

Q: A vertebra is subjected to a shearing force of 510 N. Find the shear deformation, taking the…

A: Solution: Given that Shearing force = 510 N vertebra = 3 cm diameter = 4 cm shear modulus = 8x1010…

Q: You apply a force of magnitude F1 to one end of a wire and another force F in the opposite direction…

A: Newton's second law of motion relates the net force acting on the object to the acceleration…

Q: 1. A homogeneous 800 kg bar AB is supported at either end by a cable as shown in the figure. Bronze…

A:

Q: Calculate the force (in N) a piano tuner applies to stretch a steel piano wire 8.2 mm if the wire is…

A: The solution for this question has been solved below..

Q: Which of the following represents volumetric strain? a) -ΔV/V b) ΔV/V c) Pressure/Volume d) -P /…

A: To find: Which of the following represents volumetric strain

Q: Q1: A leg has 1.4 m shaft of bone with an average cross sectional area of 3x10-4 m?. If the amount…

A: Original length of the Bone, L=1.4 m Cross sectional area of the bone, A=3×10-4 m2 contracted length…

Q: 2. Let's look at the femur – the largest, longest, and strongest bone of the human skeleton. Let's…

A:

Q: Each section of the sky way is 1.7 km long, and each segment has a cross-sectional area of 117.4 m2.…

A: In this case, the length of each section of the skyway is given. And each has some cross-sectional…

Q: Shown below is a velocity-time graph for an object being thrown up and falling back down. Velocity…

A:

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).