10. A fluid flows through a horizontal 0.1-in.-diameter pipe. When the Reynolds number is 1500, the head loss over a 20-ft length of the pipe is 6.4 ft. Determine the fluid velocity. 11. A viscous fluid flows in a 0.10-m-diameter pipe such that its velocity measured 0.012 m away from the pipe wall is 0.8 m/s. If the flow is laminar, determine the centerline velocity and the flowrate.

10. A fluid flows through a horizontal 0.1-in.-diameter pipe. When the Reynolds number is 1500, the head loss over a 20-ft length of the pipe is 6.4 ft. Determine the fluid velocity. 11. A viscous fluid flows in a 0.10-m-diameter pipe such that its velocity measured 0.012 m away from the pipe wall is 0.8 m/s. If the flow is laminar, determine the centerline velocity and the flowrate.

Name: 10. A fluid flows through a horizontal 0.1-in.-diameter pipe.When the
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 10. A fluid flows through a horizontal 0.1-in.-diameter pipe.When the Reynolds number is 1500, the head loss over a 20-ftlength of the pipe is 6.4 ft. Determine the fluid velocity.11. A viscous fluid flows in a 0.10-m-diameter pipe such that itsvelo

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Water flows steadily through the variable area pipe as shown. a) Determine the velocities in the large diameter pipe (12 cm) and the small diameter pipe (8 cm). b) Determine the discharge.
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft^3/s. Hint: You need to use the Tioga table and K value for minor losses. Z₂ = 107 ft Reservoir B 90° regular screwed elbow Pump Z₁ = 53 ft Reservoir A A) H=51+25.98(Q^2) B) H=54+24.98(Q^2) ⒸH=54+25.98(Q^2) ⠀
a 12" diameter pipe carries oil with a velocity distribution of v = 9(r1^2 - r^2) determine the average velocity and the value of kinetic energy correction
10. Water at a temperature of 800C (coefficient of viscosity is 0.357 centipoise) is flowing at a speed of 200 cm/s through a pipe of radius 2 mm. What is the nature of flow? What is the maximum velocity for it to remain laminar? What is the minimum velocity that will make the flow turbulent?
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft3/s. a. H = 51 + 25.98(Q^2) b. H = 54 + 24.98(Q^2) c. H = 54 + 25.98(Q^2)
Question 3 Water flows through a 2-in.-diameter (5.08 cm) tube that suddenly contracts to 1 in. diameter (2.54 cm). The pressure drop across the contraction is 3.45 kPa. Determine the volume flow rate. Minor Loss Coefficients for Pipe Entrances Entrance Type Reentrant Minor Loss Coefficient, Ka 0.78 Square-edged Rounded "Based on h-K(V2/2), where V is the mean velocity in the pipe. Contraction loss coefficient, K [ h = Kc \ /² ] 0.5 r/D K 0.02 0.06 ≥ 0.15 0.28 0.15 0.04 Contraction Expansion A1 A2 A₂ AR Ag/A = AR = A₁/A2 1.0 0.8 0.6 0.4 0.2 0.2 о T ° 0 0.2 0.4 0.6 0.8 1.0 Area ratio, AR 1.0 OOOO 0.8 0.6 Expansion loss coefficient, K Loss coefficients for flow through sudden area changes.
2. Glycerin at 20°C flows upward in a vertical 75-mm diameter pipe with a centerline velocity of 1.0 m/s. Determine for a 10-m length of pipe a. The head loss b. Pressure drop
B1. A crude oil of specific gravity 0.75 is flowing through a pipe of diameter 275 mm and the frictional head loss of 5 m of crude oil between the two ends of a pipe which are 525 m apart. Calculate the Reynold's Number, discharge of crude oil in the pipe. Take co - efficient of friction as 0.007 and kinematic viscosity as 10 stokes. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) The velocity of flow of oil in the pipe is (m/s) The Reynold's Number for the flow is Discharge of crude oil through pipe (in m3/s) is
Calculate the average and maximum velocities of a fluid flowing at the rate of 20 L/min through a 1 1/2 in. sanitary pipe. The fluid has a density of 1030kg/m3 and a viscosity of 50 centipoises. Is the flow laminar or turbulent?
The Darcy friction factor for both of the pipes shown is 0.024. the total flow rate is 300 m3/h. what is the flow rate through the 250 mm pipe. 325 m, 150 mm diameter a= 300 m/h 650 m, 250 mm diameter