10. A 150HP motor is to be installed on a 480 VA 3 phase motor. What is the minimum NEMAWindowMacrosSharePointstarter that should be used for this installation?SizeMaximum HorsepowerRating-Nonpluggingand Nonjogging DutyMaximum HorsapowerRating-Nanpluggingand Nonjogging DutyNEMASizeLoadVoltsSinglePhasePolyPhaseNEMASizeLoadVoltsSinglePhasePolyPhase1152002303804601152002307425...115300033805046057550......5752502041152002303804605752002303804605754050751001003.5.11520023038046057520023038046075100150200200...372101057510150200200230380460575115300*1P23040040023046030060080011520023010155752304503804605752525259009002460575Tabies are taken from NEMA Standards*1 10 hp is avaliabiaの i

Given: A 150 horsepower (Hp) motor. The motor is to be installed on a three-phase 480 V line. To…

10. A 150HP motor is to be installed on a 480 VA 3 phase motor. What is the minimum NEMA Window Macros SharePoint starter that should be used for this installation? Size Maximum Horsepower Rating-Nonplugging and Nonjogging Duty Maximum Horsapower Rafing-Nonplugging and Nonjogging Duty NEMA Size Load Volts Single Phase Poly y Phase NEMA Size Load Volts Single Phase Poly Phase 115 200 230 380 115 200 230 71½ 11 25 ... 1 15 30 00 3 380 50 460 2 460 50 ... 575 575 50

10. A 150HP motor is to be installed on a 480 VA 3 phase motor. What is the minimum NEMA Window Macros SharePoint starter that should be used for this installation? Size Maximum Horsepower Rating-Nonplugging and Nonjogging Duty Maximum Horsapower Rafing-Nonplugging and Nonjogging Duty NEMA Size Load Volts Single Phase Poly y Phase NEMA Size Load Volts Single Phase Poly Phase 115 200 230 380 115 200 230 71½ 11 25 ... 1 15 30 00 3 380 50 460 2 460 50 ... 575 575 50

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please solve this question in control system
The rotor emf of a 3-phase, 6P. 440V, 50Hz induction motor alternates at 4 Hz. What will be the rotor copper loss per phase (in kW) if the input to the rotor is 111.9kW? A. 4.23kW B. 1.86kW C. 2.98kW D. 8.95kW
The results of no-load test and block rotor tests on a three-phase, wye- connected squirrel cage induction motor are as follows No load line to line voltage: 418V No load input current: 13.3A No load input power: 1,396.5W Locked rotor line to line voltage: 154.85V Locked rotor input power: 6,840W Locked rotor input current: 57A Resistance measured between two terminals: 0.475 ohm Determine: a. resistance of the stator per phase b. resistance representing the iron losses c. magnetizing reactance d. rotor resistance per phase e. total reactance referred to the stator side
can you calculate the efficiency of the alternator
I need answer within 20 minutes please please with my best wishes
6.) . The NTD fuse rating for a 230 V, 3Ø, 50 hp synchronous motor with an 80 % power factor using the Exception Standard is A. 250 A B. 300 A C. 350 A D. 400 A
Please answer all subpart either dislike is ready Please all subpart in short please..
Q25)ii) When the speed difference will be maximum in three phase induction motor. Justify your answer
Assume that a substation supplies three different kinds of loads, mainly, S1=100KVA incandescent lights with PF1=1, S2=300KVA induction motors with PF2=0.7 lagging, and S3=100KVA synchronous motors with PF3=0.6 Leading, as shown in figure. Substation Eincandescent lights Elnduction motor loads ESynchronous motor loads The substation power factor is found from the total reactive and real powers of the various loads that are connected. Based on the given data and figure, Taking three digits after comma for PF, the total apparent power S and the total power factor PF of loads at substation will be: Select one: O a. S=394KVA & PF = 0.940 Ob. S-294KVA & PF = 1 O. S-394KVA & PF = 0.995 Od. None of these Oe. S-494KVA & PF = 0.995 Of. S=494KVA & PF = 0.940