(10) A 40mm diameter shaft is driven @ 3,600rpm by a 150kW motor. The shaft drives a 400mm diameter chain sprocket having an output efficiency of 85%. Determine (a) the torque of the shaft in kN-m (b) output force on the sprocket in kN; (c) power delivered by the sprocket in kW;

Q: the efficiency of gear train

A: Given data; The efficiency of reducer gear train=1 kWSpeed,N=1444rpmTorque=56.36 NmRatio of speed…

Q: A motor vehicle with a total weight 1361 kg has wheels of 63.5 cm effective diameter. The engine…

A: W = 1361 kgD = 63.5 cm or 0.635 m T = 203 Nm = 85% I = 7.6 kg m2 If = 0.84 kg m2

Q: mechanical engineering (Machine design) (1)Find the torque and power that a shaft with a diameter of…

A:

Q: The tune-up specifications of a car call for the spark plugs to be tightened to a torque of 38 N ⋅…

A: Given: The torque applied on the spark plug is T=38 N-m. The length of the wrench is L=25 cm. The…

Q: A drilling machine is capable of drilling 30 holes of 20mm diameter per minute in a 16mm thick steel…

A: please refer handwritten solution

Q: After the locomotive has travelled 5.83 km, the engine comes back online. What is the torque…

A: Solution: Given Data: s=5.83 kmN=230 rpmM=193 tonnes   To Find: The torque required to maintain the…

Q: How much torque must be applied to drive the screw with the applied load in units of newton meters?

A: Here,  is lead angle,  is pitch,  is mean thread diameter.

Q: A solid 38 mm diameter shaft is rotating at a speed of 510 rpm with a maximum shear stress of 78…

A:

Q: A torque of 40,000 N.m is applied to a 10 cm diameter shaft. What is the factor of safety of a…

A:

Q: Example 1.3 The blades of a wind turbine turn a large shaft at a relatively slow speed. The…

A:

Q: 4) Shafts with lengths 5m and 4 m are connected by gears. The diameter and shear modulus for both…

A: Given,  Lengths of the shafts , 5 m and 4 m. Diameter of the shafts , d = 10cm Shear modulus of the…

Q: Find the speed of shaft driven with the belt by an engine running at 600RPM. The thickness of belt…

A: When a belt connects two pulleys of different sizes, the speed of rotation of the two pulleys will…

Q: 06) A vehicle of total mass 1100 kg has road wheels of effective diameter 0.8 m and attains a speed…

A:

Q: Required inf As the hollow steel shaft shown rotates at 165 rpm, a stroboscopic measurement…

A:

Q: Suppose an automobile engine can produce 195 N⋅m of torque, and assume this car is suspended so that…

A: Given:

Q: Two parallel shafts 100 cm apart are connected by a belt drive. The driven pulley rotates at 250…

A:

Q: A rod has 14.0 kg of mass distributed uniformly over its length of 2.50 m and is suspended by two…

A: Given data as per question Mass of the rod =14 kg Length of rod =2.5 m When the rope is cut, the…

Q: An electric motor drives a compressor by use of V-belt. The pulley diameter of the compressor shaft…

A:

Q: A 4-stroke six cylinder tractor engine having a mean effective pressure of 120 psi and runs at 2,400…

A:

Q: A solid 30 mm diameter shaft is rotating at a speed of 490 rpm with a maximum shear stress of 90…

A: Diameter of the shaft, D = 30 mmRotational speed of the shaft, N = 490 rpmMaximum shear stress,  =…

Q: A hollow steel shaft with an outside diameter of 90 mm and a wall thickness of 10 mm is subjected to…

A:

Q: A hole is being drilled in a block of alloy steel with a 10-mm drill bit at a fee 0.0001 m/rev and…

A:

Q: 36 mm solid shaft is to be used to transmit 50 kW. If the shaft design is not to exceed 30 MPa,…

A:

Q: An electric motor drives a compressor by use of V-belt. The pulley diameter of the compressor shaft…

A:

Q: Q2: Detrmine the maximum Torque (T) that can be applied without exceed the shearing stressess and…

A:

Q: The Motor (J1=0.46 kg‐m2) is connected to a gearbox (J2 =0.27 kg‐m2 and J3=0.17 kg‐m2) by a steel…

A: Given Data: J1=0.46 kg-m2J2=0.27 kg-m2J3=0.17 kg-m2J4=0.37 kg-m2θ3=-2.7θ2   To Find: The equation of…

Q: On a spindle with a diameter of 100 mm and a safe shear stress of 800 kg / cm2 The attached pulley…

A: The shear stress limit will decide that by how much torque we can load the spindle such that it does…

Q: Example 1.3 The blades of a wind turbine turn a large shaft at a relatively slow speed. The…

A:

Q: I need the answer as soon as possible

A: GIVEN DATA: T=8mm=8×10-3m b=100mm=0.1m v=25m/s m=0.99kg/m μ=0.3 θ=165degreeθ=165×π/180θ=2.879 rad…

Q: A solid 30 mm diameter shaft is rotating at a speed of 490 rpm with a maximum shear stress of 90…

A:

Q: A round shaft, made of cold-finished AISI 1020 steel, is subjected to a variable torque whose…

A:

Q: On a high-speed submarine the propeller diameters are limited to 15 f t, and their maximum…

A: The aim of a propeller in submarines is to convert engine power, which is provided to the propeller…

Q: A solid steel shaft is subjected to a variable torque whose maximum value is 710 N-m. For a fatigue…

A:

Q: The shear stress at a point in a shaft subjected to a torque is  (a) directly proportional to the…

A: Write the basic mathematical torsion equation. TJ=τR=GθL Here, The torque on the object is "T" The…

Q: A rectangular key is used in a pulley connected to a line shaft at 15 kW and 600 rpm. If shearing of…

A:

Q: An electric motor drives a compressor by use of V-belt. The pulley diameter of the compressor shaft…

A:

Q: A motor with a torque of 37.26N/m and a speed of 120°/sec rotates a robotic arm that consists of two…

A: Given: The torque, T = 37.26 N.m The speed, w = 120o/s = 2.093 rad/s The diameter of worm gear, d =…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.