10-54. The smooth rigid-body cavity is filled with liquid 6061-T6 aluminum. When cooled it is 0.012 in. from the top of the cavity. If the top of the cavity is not covered and the temperature is increased by 200°F, determine the strain components E, Cy and e, in the aluminum. Hint: Use Eqs. 10-18 with an additional strain term of aAT (Eq. +4). 0.012 in in. 6 in. Probs. 10-53/54

10-54. The smooth rigid-body cavity is filled with liquid 6061-T6 aluminum. When cooled it is 0.012 in. from the top of the cavity. If the top of the cavity is not covered and the temperature is increased by 200°F, determine the strain components E, Cy and e, in the aluminum. Hint: Use Eqs. 10-18 with an additional strain term of aAT (Eq. +4). 0.012 in in. 6 in. Probs. 10-53/54

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The state of strain at the point on the gear tooth has components €x = 850(106), €y = 480(106), Yxy = 650(106). Use the strain-transformation equations to determine (a) the in-plane principal strains and (b) the maximum in-plane shear strain and average normal strain. In each case specify the orientation of the element and show how the strains deform the element within the x-y plane.
The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.47 in., -0.16 in.). Assume a - 17 ft, b-34 ft, c-12 ft, and d - 24 ft. Determine the normal strain in each bar. Answer: EAB- T EBC i P a e (1) B UE με b (2) C d
The stress–strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length of 2 in. is given in the figure. If the specimen is loaded until it is stressed to 70 ksi, determine the approximate amount of elasticrecovery and the increase in the gage length after it is unloaded.
Four stress elements are shown below. All members have the same value for E (Young’s Modulus) and ν (Poisson’s ratio). Rank the members from largest to smallest absolute value of the normal strain in the y direction.
A tri-axial state of stress, σx , σy, and σz ,exists in a steel machine part. For steel, E = 200GPa and ν = 0.3. Determine the normal strain in the x-direction if σx = 100MPa, σy = 35MPa, σz = 70MPa. Determine the dilatation. Determine the modulus of rigidity.
8-21. The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm and a gage length of 50.8 mm. When the applied load on the specimen is 50 kN, the diameter is 12.67494 mm. Determine Poisson's ratio for the material. 8-22. The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm and a gage length of 50.8 mm. If a load of P = 60 kN is applied to the specimen, determine its new diameter and length. Take v = 0.35. σ (MPa) 490 0.007 Probs. 8-21/22 € (mm/mm)
The strain components ɛx = 466 µE, ɛy = -524 µe, and yxy = -646 µrad are given for a point in a body subjected to plane strain. Determine the angle Op corresponding to the orientation of the principal planes at the point. -12.12° None of the above -17.93° -13.75° -10.36° -16.56°
The rectangular plate is deformed into the shape shown by the dashed lines. For a 283 and b-407. determine the normal strain along the line of AC. [103] (sign sensitive) Junit mm (not in scale) CTNL с b D-6 X-7.5811 a I 10 I