1.d) Arrange the following steps in the correct order for a 3D printing workflow. -3D print -Export G-code -Slicing -CAD design -Export part 1.e)Which of the following is the most suitable application of 3D printing technologies? a) Rapid prototyping b) Mass production c) Replacing traditional subtractive manufacturing d) Cost-effective alternative to injection moulding 1.f) What makes 3D printing superior to traditional manufacturing technologies? a)Customisation b) Efficiency c) Speed d) Quality

Q: to make one revolution. The rough a gear reduction unit motor driven belt pulley 77

A: Given-Information:- Number of Holes, 40 per min Energy per hole, 10 kN-m = 10,000 N-m Diameter, d =…

Q: CALCULATE ROTARY MECHANICAL POWEA Calculate the power in Hp at a gear shaft given the following…

A:

Q: A metal disc of 20mm diameter is to be punched from a sheet of 2mm thickness. The punch and the…

A: Given operation is blanking operation. Blank operation  = D = 20 mm Sheet thickness = t = 2mm…

Q: The drilling time (in minute) is

A: Given, Diameter,d= 20 mmThickness,t= 40 mm N= 400 rpmFeed rate,f= 0.1 mm/revDetermine the drilling…

Q: 8. A hole of 20 mm diameter is to be drilled in a steel block of 40 mm thickness. The drilling is…

A: Solution:-Given thickness of steel block=40 mmapproach and over run together=d2=10 mmrotational…

Q: the blanks: the center distance in (cm) of 4 direct contact rolling.cylinders. Cylinders A-D have a…

A:

Q: The Ray Precision Engineering company uses CNC Lathe machine. The reliabilit of Gear Box of CNC…

A:

Q: 3. Design Challenge: The wind turbine is designed to generate 2.5 MW of power with the blades…

A: Given: To find: design the shaft

Q: calculate the speed (rpm)

A: calculate the speed (rpm)

Q: submit any example for shaft and gear and design them finding the bellow 1- the contact stress for…

A: given; (a)the contact stress for the shaft and gear (b)the bending stress for the shaft and gear

Q: When designing a shaft, where (what locations) do you need to need to check the diameter of the…

A: While designing a shaft, the diameter of the shaft is checked at the critical points . Critical…

Q: A hydraulic press is used to apply 500 lbs of force to press fit an assembly. The cylinder has a 2"…

A: The objective of the question is to calculate the flow rate required to retract the hydraulic press…

Q: In a lathe machine, the maximum torque transmitted by a shaft exceeds the mean torque by 19 %. A…

A:

Q: State law of gearing? What do you understand by the term ‘interference’ as applied to gears?

A: To find:- Law of gearing and Interference

Q: Calculate: (i) Indicater power; (ii) Brake power; (iii) Mechanical efficiency.

A: Given data, Following observation were recorded during a test on a single cylinder oil…

Q: ne lead screw of a lathe has Acme threads of 40 mm outside diameter d 6 mm pitch. The screw must…

A:

Q: Energy required to cut a hole. Energy required for cutting work per second. Maximum fluctuation of…

A:

Q: When does the Stress concentrations occur in shafts?

A: A resisting force produced in a body on each unit area to counter the deformation of the body is…

Q: 1.Power is to be transmitted from one shaft to another which is parallel. The shafts are 9 inches…

A:

Q: Please write the NC code for machining this part in Fanue system.

A: this question is about topic of CNC machining in production engineering subject. The NC code for…

Q: 500 rpm, the follower is to be held against the cam by a helical compression spring with a force…

A: Given data- 1.cam running at =500 rpm 2.force on helical spring =80 lb-160 lb  355.8 N-711.7 N…

Q: -differe nce b etwee

A:

Q: Define; (a) Cut-in speed, (b) Cut-out speed, and (c) Betz limit

A: (a) Cut-in speed It is defined as a minimum speed at which the turbine starts generating…

Q: Calculate the minimum length of a parallel key for a gear which is to be mounted on a 60 mm diameter…

A:

Q: ) The clearance. b) The whole depth. c) Dedendum.

A: here, you post more than 3 subparts as per honor code and answering guidelines I can answer 1st 3…

Q: 4. In casting, dimensions are expressed to apply allowances accordingly.

A: A manufacturing process in which the hot and melted liquified metal is poured into a cavity so that…

Q: required punch diameter ?

A: Given data;   A meatal disc is to be punched having following data,i.e,  Diameter,d=30 mm…

Q: An engine, running at 350 r.p.m., drives a line shaft by means of a belt. The engine pulley is 950…

A:

Q: In a lathe machine, the maximum torque transmitted by a shaft exceeds the mean torque by 18 %. A…

A: Given, P=3 kW=3×103 WN=625 rpmTmax=1.18Tm

Q: 7. A 4" diameter cylinder with a 1" diameter rod and a 12" stroke length needs to fully retract in 2…

A: The diameter of the cylinder is D=4'' The diameter of the rod is d=1''. The stroke length is l=12''.…

Q: A six-cylinder two-stroke engine with a compression ratio = 9 produces a torque of 1100 Nm at a…

A: Given data: Number of cylinder in engine (n)=6 Compression ration (r)=9 Speed (N)=2100 rpm Torque…

Q: A medium drive of a steel hub of a gear with an outside diameter of 80 mm on a steel shaft is…

A: Given Data: Steel hub gear outside diameter Do=80mm The basic size of the hub and shaft D=49 mm Sol:…

Q: Explain about derivation of shaft strength...?

A: Derivation of shaft strength ;

Q: Power is supplied at the rate of 0.40 hp for 2 min in drilling a hole in a 1.0 lb brass block. (a)…

A: Given Data  Power supplied at a rate of 0.40 hp for 2 min Work=Power×time Work=0.40(hp)(2×60)Work…