1.8 m PROBLEM 1: A solid shaft shown in Figure 1 is made of steel with a diameter of50mm, use shear modulus for steel, 78 GPa. Determine the following: a) the angle of twist at A( b) the angle of twist at A, assuming that the steel shaft is hollow with a 28 mm-outer diameter and a 18-mm inner ,and 250 N-m diameter Figure 1

1.8 m PROBLEM 1: A solid shaft shown in Figure 1 is made of steel with a diameter of50mm, use shear modulus for steel, 78 GPa. Determine the following: a) the angle of twist at A( b) the angle of twist at A, assuming that the steel shaft is hollow with a 28 mm-outer diameter and a 18-mm inner ,and 250 N-m diameter Figure 1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Help please!
Q3: Three segments of elliptical solid steel section, circular solid aluminum section and circular solid bronze section were assembled to form the shaft shown in Figure (3). Determine the generated stress in each material when the support at D is able to rotate until 0.035 radian based on the two torques T1 and T2 of 450 N.m and 750 N.m, respectively. 94= 834 v5? AL:28 1 Steel Ahminum Bronze T2 D= 70 mm D= 100 mm 1.5 m 1.5m 2.0 m 25 mm Figure (3) 145 mm
3.1 Show your complete solution.
QUESTION 2) The shaft, first two meters length has a solid cross-section with a diameter of 6 cm and the last one meter length has a hollow cross-section with a inner diameter 5 cm and outer diameter of 6 cm is shown in the figure. If the allowable shear strength tu-35 MPa and shear modulus G=200 GPa, determine the allow magnitude of the torsional moment M for a safe structural system. M M бст IScm B C D lm Im 1m
Problem- A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm, respectively. An axial load of 12kN is applied on the bar. E= 2 × 10 N/mm². The elongation of the bar will be
Several torques are applied to the stepped shaft (G= 80 GPa) shown in Fig. 1. Neglect any Stress concentrations associated with the sudden change in cross-section. Determine: (a) The maximum shear stress in the shaft (b) The rotation of the end E relative to the end A. 500 N-m 300 N-m FC 30 mm 400 mm A C 150 N-m 300 mm 350 mm D 50 N-m E 450 mm 20 mm
Q 3. A rigid beam AB is 5.5 m long, hinged at point A and supported by two pipes at C and D as shown in figure 3 below. Pipe 1 at C is of copper has a outer diameter of 120 mm and inner diameter of 100 mm and yield stress of copper is 138 N/mm² Pipe 2 at D is of steel has a outer diameter of 100 mm and inner diameter of 90 mm and yield stress of steel is 250 N/mm2 Calculate the safe load at A if the load factor is 1.66 Pipe 1 Pipe 2 Psafe 2.3 m 2 m C 5.5 m Angle ACE = 0 Figure 3 Angle BDF = 42° Take 0 = 10 Page 7 of 7 PTO
A thin beam with a solid rectangular cross-section is loaded as shown in Figure Q7 below. W W L/3 L/3 L/3 Figure Q7 What is the ratio of the maximum to nominal shear stress for the beam described in Question 7? O a. 3:2 O b. 1:4 Ос. 3:1 O d.2:1 O e. 1:2 O f. None of the provided answers are correct. O 8. 1:1
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 20.11 lb.
The plate has a thickness of 20 mm and the force P = 5 kN acts along the centerline of this thickness such that d = 150 mm. (Figure 1) Figure d‡ 200 mm a 1 of 1
Problem 6 For the structure shown in the figure, determine the normal and shear stresses at point A on the cross section of the pipe. at section a-a. mun 40 mm 300 mm 300 mm