The following beam is supported by three cables AD, BE, and CF. Cables AD and CF are made of steel, and cable BE is made of aluminum. The data is presented in the table. A force P of 125 kN is applied, and the temperature increases by 100°C. Determine:The stress in each cable. Answ: 25.09 MPa, 49.22 MPa.The vertical displacement of the beam. Answ: 1.99E-3 m. 1.5 mDA1.2 mEFBCYP Aluminum cableSteel cableElastic modulus, EDiameter, D Coefficient of thermal expansion70 GPad₁ = 50 mm200 GPad₂ = 75 mm23.6E-06/C12E-06/C

Same values is came once refer explanationExplanation:Step 1: Step 2: Step 3: Step 4:

Answered: 1.5 m D A 1.2 m E F B C YP Aluminum…

1.5 m D A 1.2 m E F B C YP Aluminum cable Steel cable Elastic modulus, E Diameter, D Coefficient of thermal expansion 70 GPa d₁ = 50 mm 200 GPa d₂ = 75 mm 23.6E-06/C 12E-06/C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the maximum bending stress and shear stress on the same section.

A: Bending moment at the section B=Mb =90×0.2-20×0.2×0.1=1.4 kN-m=1.4×106 N-mm Moment of inertia,(I)…

Q: Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a…

Q: curved-beam formula to compute the bending stress.

Q: The shaft shown is supported by at A and at C. If the material has an allowable bending stress of 24…

A: The bending equation is as follows, σy = MIWhere,σ = Bending stressy = Distance between neutral axis…

Q: The Link AB must be made of steel with a maximum normal stress of 450 Mpa. Any stress above that…

Q: Three cables having an area of 0.05 in? each is carrying the load W as shown. With no stress, the…

A: Given, A = 0.05 in2 E = 29000 ksi

Q: Compute the maximum load P (in kiloNewtons) so as not to exceed the compressive stress of 75 MPa and…

A: To find out the maximum load P that can carry maximum tensile load 100 Mpa and compressive load 75…

Q: The rigid bars shown are separated by a roller at C and pinned at A and D. A steel rod at at B helps…

Q: determine the largest allowable spacing of rivets that join (a) the angle bars and the top plate;…

A: The Working stress of shear and bearing is given as 100 and 250 MPA yu

Q: depth of the neutral axis.

A: Given: Width of the beam, b = 200 mm Depth of the beam, D = 400 mm Clear cover, cc = 40 mm Diameter…

Q: В 12 kN For the frame and loading shown, determine the components of the forces acting on member…

A: To find forces acting at B and D

Q: The center post B of the assembly has an original length of 124.4mm whereas posts A and C have a…

A: To determine the average normal stress in the posts. Given, Length of posts A and C (L1) = 125 mm…

Q: A beam is used to support a concentrated load of 12 kN and a distributed load (w). The beam has the…

A: Maximum bending stress: The maximum stress that a member of a structure experiences by the load…

Q: C 105° SIMPLE STRESSES 50° D 65° 1. Two steel bars are connected by two 20 mm 60 KN 15° BLOCK E…

A: At joint B Consider the summation of forces in the vertical direction TBC sin65o+TBD…

Q: a = 11.7 x 10/°C E = 200 GPa A = 1,200 mm2 a = 23 x 10/°c E = 70 GPa A = 900 mm2 200 kN 300 mm 200…

A: Coefficient of thermal Expansion = 11.7 x10-6 / Co Young`s modulus = E ab = 200 x 10 3 Mpa Area of…

Q: An assembly of bars are designed in Figure 1: The assembly is made of structural A-36 steel where…

Q: V. Knowing that the rectangular section beam shown is made of steel for which the allowable stress…

Q: Q4 - For the given beam and cross section, at point B on section A-A (mid-span), determine the…

Q: An I section girder or stanchion is constructed from two 80mm x 12mm flanges joined by an 80mm x…

A: I section girders: I sections girders are most commonly used in the construction of bridges. These…

Q: AP 35° 35°

Q: H.W No.1: The concrete I-beam of figure is pretensioned with four bounded stranded cables having…

Q: Prob 2. The rigid bar below is supported by two copper bars (Ecopper = 90 GPa) and two brass bars…

A: Given data : Ecopper = 90 Gpa , Ebrass= 120 Gpa , diameters of all bars = 20mm , Load = 20000 N Find…

Q: AW250 x 32.7 structural steel [E = 200 GPa] wideflange shape is loaded and supported as shown. A…

Q: The lap joint is fastened with four 3/4-in.-diameter rivets. The working stresses are 14 ksi for the…

A: Given Shear stressτ=14ksi=14000psiBearing stress σb=18ksi=18000psiDiameter,d=34inThickness,t=78in To…

Q: A vertical cylindrical, wooden-stave barrel is 3.5 ft in diameter and 5 ft high, and is open at the…

A: Given Dimeter of wooden stave barrel = 3.5 ft Height of wooden stave barrel = 5 ft Specific gravity…

Q: SITUATION The homogeneous bar ABCD shown is supported by a cable that. runs from A to B around the…

Q: PROBLEM: Prove that the truss shown is statically determinate and solve for the force members. State…

A: Truss, no.of members = 21 no.of joints = 12 Length of the truss = 3+3+3+2+2+2 = 15m Height of truss…

Q: Find the forces in members AB, CD for the truss shown below. 20 KN B A 2m C 2m D 30 KN 2m 10 KN E F…

A: Given data :-One truss is shown into the diagram given in the question.Required that :-Find the…

Q: FOR THE TRUSS SHOW BELOW, SOLVE FOR THE STRESSES (ORANGE) IF ALL MEMBERS 750 mm^

Q: Calculate the maximum tensile and compressive stresses in the section of BC of the beam. A 0.5 in…

A: Determine the maximum tensile and compressive stress in the section BC.

Q: What are the highway culvert design criteria and sizing principles, what risks they are exposed to…

A: Brief concept introduction- Highway culvert- A highway culvert is a drainage system that allows…

Q: P6-5. Sketch the bending stress distribution over each cross section. (a) M P6-5 (b)

A: Two members cross section are shown in the above figure. We have to draw bending stress distribution…

Q: The load on the bearing of a cast-iron bracket is 5 kN. The form of the section AB is given.…

Q: From the figure as shown, the cable BC supports the horizontal bar AB. Compute the shear stress at…

Q: A 1 2-inch diameter solid round steel bar must transmit a torque of 6000 in-lb and another moment…

A: If the force can cause the deformation of a material by slippage along the plane or parallel to the…

Q: 4m 60⁰ 2kN C 60⁰ 2kN B 8m 30⁰ 2kN A

A: Cut the x-x plane as shown in below solution. Applying equilibrium equation in both x and y…

Q: A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three…

A: Given:A=1020 mm2a=1.5 mb=8.2 mc=3.7 mP=40 KNQ=85 KNSince, support A is roller and C is hinged.…

Q: *8-36 The frame supports a centrally applied distributed load of 1.8 kip/ft. Determine the state of…

Q: In the truss shown in Figure. Determine the force member at AC. * 400 kN 800 kN 6 m D 3 m A: F 3 m 6…

Q: Determine the maximum tensile or compressive stresses in the beam due to bending. The section has a…

Q: Rigid member ABC is supported by a wire BD at B and a pin support at C as shown below. The failure…

Q: The beam shown below has a cross section of channel shape with width b-400 mm and height h=80 mm,…

A: Given data:

Q: AW250 x 32.7 structural steel [E = 200 GPa] wideflange shape is loaded and supported as shown. A…

Q: Determine the largest weight W that can be supported by the two wires AB and AC. The working…

A: Determine the largest weight W that can be supported by two wires AB and AC

Q: COMPUTE THE SHEARING STRESS IN THE PIN AT B FOR THE MEMBER SUPPORTED AS SHOWN IN THE FIGURE. THE PIN…

Question

The following beam is supported by three cables AD, BE, and CF. Cables AD and CF are made of steel, and cable BE is made of aluminum. The data is presented in the table. A force P of 125 kN is applied, and the temperature increases by 100°C. Determine:

The stress in each cable. Answ: 25.09 MPa, 49.22 MPa.
The vertical displacement of the beam. Answ: 1.99E-3 m.

Aluminum cable
Steel cable
Elastic modulus, E
Diameter, D Coefficient of thermal expansion
70 GPa
d₁ = 50 mm
200 GPa
d₂ = 75 mm
23.6E-06/C
12E-06/C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step by step

Solved in 1 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

asap please thank you
Which of the following is the nearest value for the force at member BD? a. 5kN tension b. 1.7 kN tension c. 5 kN compression d. 1.7 kN compression
For the beam and loading shown, consider the n-n section. (a) Absolute value of shear force in n-n section |V| In kN units, (b) the absolute value of the shear stress at point a of the n-n section |τ| Specify in MPa units. Take the P value of 34 kN and the D value of 17 mm in the question.
answer only letters D and E
The beam shown below has a cross section of channel shape with width b=200 mm and height h=80 mm, the web thickness is t=12 mm. Determine the maximum tensile and compressive stresses in the beam due to uniform load. And draw. 200 mm 3.2KN/ 2 KN.M BO 80mm 12mm 3m 1.5m
Q4: determine the maximum tensile and compressive stresses acting normal to the beam. 50 mm 10 kN 100 mm 30 kN 6 m 2m B (2
5-83 The A-36 steel shaft is made from two segments: AC has a diameter of 0.5 in. and CB has a diameter of 1 in. If the shaft is fixed at its ends A and B and subjected to a uni- form distributed torque of 60 lb in./in. along segment CB, determine the absolute maximum shear stress in the shaft. 5 in. 0.5 in. 20 in. 60 lb-in./in. 1 in. B Prob. 5-83
Calculate the maximum moment (with diagram) & maximum shear (with diagram)
F5. The circular shaft AC is fixed to rigid walls at A and C. The section AB is solid annealed bronze and the hollow section BC is made of aluminum alloy 2024 T-4. There is no stress in the shaft before the 20,000 ft-lb torque is applied. Determine the maximum shearing stress in each shaft after T is applied. Section BC 4 D=4" 20 ft-k 6.5-FE B 5ft Match each item to a choice: TAB TBC 2"
Determine the largest weight “W” that can be supported by the two wires AB and AC. The working stresses are 100MPa for AB and 150MPa for AC. The cross sectional area of AB and AC are 400mm2 and 200mm2.