1.5 Develop an expression for the thermal efficiency of the air-standard diesel cycle as a function of the compression ratio r. = V1N2 and the expansion ratio re = V4 / V3. Assume the working fluid is an ideal gas, and the volume effect of moles of gas generated is small relative to the effect of heating from combustion.

1.5 Develop an expression for the thermal efficiency of the air-standard diesel cycle as a function of the compression ratio r. = V1N2 and the expansion ratio re = V4 / V3. Assume the working fluid is an ideal gas, and the volume effect of moles of gas generated is small relative to the effect of heating from combustion.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At the beginning of compression, Otto cycle works on 0.2 lb/s of air at 14 psia and 1300F. The temperature at the completion of combustion is 45000R, the compression ratio is 5.5, and the hot-air standard is k = 1.3. a. Find V1 , P2 , T2 , P3 , V3 , T4b. Compute the heat added (QA),heat rejected (QR), work (W) andthe cycle efficiency (e).
Help, please answer carefully. Wrong answer was given, answer with step by step solution please thank you.
1. An ideal air-standard diesel cycle with inlet conditions: 21.11˚C and 14.7 psia, 700 Btu/lbm heat input, and a compression ratio of 15. Find P2, T2, T3, V3, P4, T4, and the efficiency of the cycle. Take Note: Assume air standard values for R and k Cp = kR/k-1 Cv = R/k-1 a. Find the value of P2. (in psi or lb/in^2) b. Find the value of T2. (in Rankine) c. Find the value of T3. (in Rankine) d. Find the value of V3. (in ft^3/lbm) e. Find the value of P4. (in psi or lb/in^2) f. Find the value of T4. (in Rankine) g. Find the value of efficiency of the cycle. (ex. 100-%)
An ideal air-standard Brayton cycle operating at steady state produces 10 MVWof power. Operating data at principal states in the cycle are given in the table below. The states are numbered as in the figure below. State p(kPa) T (K) h (kJ/kg) 1 100 300 300 1000 574.1 579.7 3 1000 1800 2002 4 100 1034 1085
A diesel cycle with air as the working fluid has a compression ratio of 20. The temperature and pressure in the first process is 20°C, 95kPa and the highest attainable temperature is 1927°C. The air standard assumptions are applicable, both Kinetic and Potential energy are negligible. The mass/mass flow rate is negligible. Use the standard constants for air (Cp, Cy. R, and k). Determine the amount of heat transferred and rejected, the net work and thermal efficiency, and the mean effective pressure.
4
Q3: An ideal air-standard Diesel cycle engine has a compression ratio of 18 and a cut- off ratio of 2. At the beginning of the compression process, the working fluid is at 100 kPa, 27°C. Determine the temperature and pressure of the air at the end of each process, the net work output per cycle [kJ/kg], and the thermal efficiency.
3. Air is used in an ideal Brayton cycle (shown in p-v and T-s diagram). The state conditions are given in the following Table. (a) The heat addition and heat rejection (b) The net power developed per unit mass flow rate (c) The thermal efficiency State T(°C) P(kPa) 1 20 100 3 1000 350 T 3 3 b a 2.
Draw the Organic Rankine Cycle (ORC) diagram, including its main components. Subsequently, for each component in the cycle, formulate an energy balance and a mass balance. Your diagrams should be clearly labelled, and your balances must be accurately presented.
Assume a basic (non-regenerative) ideal Brayton cycle where air modeled as IG with variables specific heat. The gas-turbine engine has the following operational parameters: Inlet Air Temperature:537 R Inlet Air Pressure:14.696 psia Compressor Pressure Ratio (rp):6.0 Firing Temperature:2400 R Heat Recovery Steam Generator: Assume that the exhaust from the gas turbine engine is directed to a heat recovery steam generator (HRSG)to produce wet steam (i.e. saturated vapor) at a pressure of 600 psia. Liquid water is supplied to the HRSG at 100F and 600 psia. The exhaust gas from the gas-turbine engine leaves the HRSG at the saturation temperature of the wet steam. With these conditions determine: a) the exit temperature of the wet steam (F), b) the intensive steam production rate, lbm-steam/lbm-exhaust gas. Absorption Chiller CHP: Assume the process steam from the HRSG is now used to drive an absorption chiller with COP of 0.7, and that the mechanical power of the gas-turbine engine is used…
THERMODYNAMICS