1.3-20 A plane frame is restrained at joints A and D, as shown in the figure. Members AB and BCD are pin connected at B. A triangularly distributed lateral load with peak intensity of 80 N/m acts on CD. An inclined concentrated force of 200 N acts at the mid- span of BC. (a) Find reactions at supports A and D. (b) Find resultant forces in the pin at B. B -Pin connection 1.5 m 4m A 1.5 m 200 N 4m D 80 N/m

Q: A truss is subjected to a 12 Kips of vertical load at G, a 42 Kips of vertical load at F and a 18…

A:

Q: A bent beam ABCD is held in equilibrium by a roller at A and by a pinned connection at D. The beam…

A:

Q: A bent pipe is attached to a wall with brackets as shown. A force of F= 235 lb is applied to the end…

A: Given data:Force, F = 235 lba = 12 inb = 27 inc = 20.3 ind = 75 inh = 42.5 ing = 50 inAssume D is…

Q: segment CB, as shown in the figure. The bar is supported by a pin at point B and a cable CD is…

A:

Q: METHOD OF JOINTS * The Cantilever truss in figure below is hinged at D and E. Find the force in each…

A: The forces in each member of the truss are: ◆ FAB = 2000 lb ...(Tension) ◆ FAC = -1732.05 lb…

Q: A frame structure, as shown in the following diagram, is given. Calculate: (a) Reaction forces at…

A:

Q: A sign ABCD is constructed from 7 mm thick plate steel (density p=8000 kg/m³) with the geometry…

A: To find:Determine the reaction forces at A and E. Given data:A sign ABCD is constructed from a steel…

Q: A plane frame with pin supports at A and Ehas a cable attached at C, which runs over a…

A: a.Free body diagram:   No horizontal force on frame,henceEx=0Now,Ey+Ay=500lb⇒Ey=500lb-AyNow,Net…

Q: Consider the frame shown in Fig 4. A 100N load is suspended around a fixed drum with radius 2 m…

A: Draw the free-body diagram of the frame.

Q: The vertical structure ABCD shown in Figure 1(a) is subjected to a (a) system of coplanar forces and…

A: Draw free body diagram and find reaction at roller support A.

Q: A horizontal L=1.2 m long mb=14 kg uniform bar is hinged on the left end and pulled at the right end…

A:

Q: A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in…

A: Given data:- A two-story building P1=400 KN P2=720 KN L=3.75 m To find:- Internal axial force axial…

Q: Problem 2.2-14 The frame construction of a factory workshop is built from two angled girders that…

A: The value are

Q: Т2 KN KN MPa MPA MPa MPa

A: Given data as per questiondimensions of  steel plate = 2.5 x 1.5 x 0.08 m weight of the steel plate=…

Q: The frame shown in the figure is loaded as shown. (a) Draw the FBD for the frame. (b) Determine the…

A: The FBD for the frame is given below,

Q: M C a In the figure above, g = 3, f = 7, d = 7.616, a = 5.2m, b 3 2.2m, с — 1.2т and @ — 28° A…

A:

Q: Frame ABCD as in Figure Q1 is pin connected at A and roller supported at B. (a) Sketch the free body…

A: Given data  Given force system

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.