1.26 PSPICE MULTISIM The voltage and current at the terminals of an automobile battery during a charge cycle are shown in Fig. P1.26. a. b. Calculate the total charge transferred to the battery. Calculate the total energy transferred to the battery. v (V) 15 10 5 i (A) 30 20 10- 5 5 10 15 20 25 10 15 20 25 t (ks) t (ks)

Q: A diode has Is = 10-¹7 A and n = 1.07. (a) What is the diode voltage if the diode current is 70 µA?…

A:

Q: Assume each diode to be OFF when V₂ ≤ 0.7V and ON when VĎ >0.7V. Find iD1, İD2, İD³, and vō in each…

A: Given:a circuit,when , the diode is off. when , the diode is on. Find:iD1, iD2, iD3 and v0.

Q: The following waveform pattern is for the output X and inputs A, B - ப ×.ப 2-input AND gate 2-input…

A: For the given waveform findout the logic gate.here A and B are inputs and X is output.We need to…

Q: For the fixed -bias Configurahion of Figure 1, delermine : a) I BQ b) Ice c) VCEQ O1GV Ice Figure 1…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Table 3 6. Plot the values from Table 2 and Table 3 on the same graph done in step 3. Does the diode…

A: Diode is device which is made of semiconductor, basically it act as switch

Q: Draw a schematic of  the full-adder using a single 74153 IC.

A: Given: IC 74153 To do: Draw a schematic of  the full-adder using a single 74153 IC.   Note: As…

Q: The diodes in the circuit in Figure Q7 have V₂ = 0.7. Determine the output voltage Vo and the…

A: Given, Vγ=0.7V1=2VV2=3VTo calculate,Vo=?ID1,ID2,ID3  and I

Q: For the fixed -bias Configuralion of Figure 1, defermine: a) I BQ glev I6V b) Ice c) VCEQ Figure 1…

A: In this question,   We need to determine the voltage VCEQ  , VC  and base voltage and emitter…

Q: The resistance of 125 strain gauge changes by 1 Q for 4000 micro- strain. The gauge factor for…

A: Given: Resistance, R=125 Ω Change in resistance, ∆R=1 Ω Strain, ∆ll=4000×10-6 strain

Q: Fill up the below state table by converting the most right two digits of the number 88 72 18 to BCD…

A: According to the question, we need to fill up the below state table by converting the most right two…

Q: There are no classes .summer at in on

A: There are no classes in summer

Q: Rc does not look like a standard resistor value? and what about choosing value for Re, it has to be…

A: The above question is based on BJT circuit analysis.

Q: Choose the correct statement O MOSFET is a current controlled device O MOSFET is a uncontrolled…

A:

Q: For the voltage -divider bias configurakon in Figure I, determine: p16V a) Ise b) Ice 62ka 3.9kn…

A: The thevenin equivalent of the circuit will be…

Q: Describe the consequences of each defect. 1) LED on switch C input is open 2) 7447A Input Opened…

A: The experiment done is for the basic of 7 segment. 7 segment to work correctly , making the correct…

Motor Load, Torque, and Power Quality Requirement

An electric motor is a gadget that changes electrical energy into mechanical energy over to follow up on a mechanical burden. The weight set on the motor because of this mechanical movement is known as motor load. Appropriately matching the motor burden to the engine is vital to forestall harm to the engine or wasteful and unnecessary expensive activity. Engines perform such undertakings as moving a thing starting with one spot then onto the next, cutting it, changing its shape, etc. The motors might be evaluated as far as a few variables including power yield, voltage, current, and temperature. Harm to an engine might happen when it is worked under over the top engine load contrasted with its appraised limit.