1.10 As shown in Fig. E1.10, a cone was rotatedaround the center-vertical axis, the distance 8between the cone and the fixed suface is 1mmlubrication oil ( u =0.1p.s) fills the gap. When theangular velocity w is 16s', the bottom radius Rof cone is 0.3m H = 0.5m Calculate the torqueneeded.2RFIGURE E1.101

Answered: Image /qna-images/answer/2160b93b-45d2-4d45-b426-d9d2b4c2097b.jpg

1.10 As shown in Fig. E1.10, a cone was rotated around the center-vertical axis, the distance 8 between the cone and the fixed surface is 1mm lubrication oil (µ =0.1p.s) fills the gap. When the angular velocity w is 16s², the bottom radius R of cone is 0.3m H = 0.5m Calculate the torque needed 2R FIGURE E1.10 H

1.10 As shown in Fig. E1.10, a cone was rotated around the center-vertical axis, the distance 8 between the cone and the fixed surface is 1mm lubrication oil (µ =0.1p.s) fills the gap. When the angular velocity w is 16s², the bottom radius R of cone is 0.3m H = 0.5m Calculate the torque needed 2R FIGURE E1.10 H

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. The bulk modulus of compression......... (a) is independent of temperature of pressure and viscosity (b) increases with the pressure (c) is independent (d) has a dimensionless unit 6. If a non-uniform solid body weighs 500 N in air and when it is completely submerged in water its weighs is 300 N. If it has a volume of 0.0136 m³ then its specific gravity is.......... (c) 2.5 (d) 3.0 (e) none of these (a) 1.5 (b) 1.7 7. A flat plate of area 1.5 m² is pulled with a speed of 0.4 m/s relative to another plate with a distance of 0.15 mm clearance between them. For a fluid viscosity of 0.1 Pa.s, the power required to maintain this speed is (a) 160 W (b) 100 W (c) 200 W (d) 400 W 8. A solid wooden cylinder (SG = 0.6) has diameter of 0.8 m and a height of 3 m, when the cylinder is floating vertically on its base in water then the submerged height of the cylinder is. (a) 1.1 m (b) 1.4 m (c) 1.8 m (d) 2.6 m 9. A wooden cube (SG=0.6), its base 5 cm x 5 cm and has 10 m height, floats vertically…
A silicon carbide ball with 5 mm in diameter has volume based CLTE (a,) of 8.1 x106/°C. If the ball is heated from 100 to 1750°F, calculate the increase in diameter. Convert first the temperature to °C. Note: (AV/V) = (V-V.)/Vo= av AT
Use the provided data wherever you need. ((transmitted power 0.050 MW, speed 500 rpm, Modulus of Elasticity 220 GPa, Modulus of Rigidity = 70 GPa, Ultimate stress = 620 MPa, Compression stress = 240 MPa, Yield stress 440 MPa, Shear stress = 120 MPa, F.S. = 4, Bending moment 0.5 KN m, diameter of rivet 10 mm, pitch 50 mm)). Q2. For the 50 mm shaft shown in figure. 2. If a torque T and moment M are applied to the shaft, use the suitable theories to design the welding joint. Check the whole system. M 以 Figure 2
Please solve! Find the air horsepower of an industrial fan that delivers 55 000 cubic feet of air per minute through a 3 ft. by 4 ft.; pressure is 5 in. of water; air temperature is 700 F and barometric pressure is 29.92 in. of mercury.
Given: • Weight of person on merry-go-round = 60 lbs • Force person on merry-go-round is able to hold on with = 60 lbs • radius of bar person is holding onto = 2.2 feet • merry-go-round is accelerated for 5 seconds Find: • maximum tangential acceleration for person to not let go = Your Answer: ft/s^2
The power provided by a centrifugal pumo is given by P=mgh where P = power/watts m = mass flow rate, kg/s g= gravitational acceleration, m/s² h = pump head,m prove that this equation is dimensionally homogeneous
How can the equivalent point forces of fluids be found?
5. A 12-in.-diameter circular plate is placed over a fixed bottom plate with a 0.1-in. gap between the two plates filled with glycerin as shown in Fig. P1.4. Determine the torque required to rotate the circular plate slowly at 2 rpm. Assume that the velocity distribution in the gap is linear and that the shear stress on the edge of the rotating plate is negligible. Ans. 0.0772 ft-lb CHAPTER 1 Torque Rotating plate 0.1 in gap Figure P1.4: Illustration for Example 1.5 FLUID PROPERTIES
please answer again the image posted for formula can't be load.
questin 3a
A spherical tank of 1.2 m radius is half-filled with oil of relative density 0.8. If the tank is given a horizontal acceleration of 10 m/s2, calculate: The inclination of the oil surface to horizontal in degrees a. 0.792 b. 1.077 c. 9.4 d. 45.55