Ezample 2.17: A ship displacing 1000 tons has the horizontal cross section at water line shown in Fig. 2.41. Its center of buoyancy is 6.0 ft below water surface, and its center of gravity is 1.0 ft below water surface. Determine its metaeentric height for rolling (about y-y-axis) and for pitching (about z-z-axis).

Ezample 2.17: A ship displacing 1000 tons has the horizontal cross section at water line shown in Fig. 2.41. Its center of buoyancy is 6.0 ft below water surface, and its center of gravity is 1.0 ft below water surface. Determine its metaeentric height for rolling (about y-y-axis) and for pitching (about z-z-axis).

Name: Ezample 2.17: A ship displacing 1000 tons has the horizontal cross se
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Ezample 2.17: A ship displacing 1000 tons has the horizontal cross section atwater line shown in Fig. 2.41. Its center of buoyancy is 6.0 ft below watersurface, and its center of gravity is 1.0 ft below water surface. Determine itsmetaeentric height

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. The bulk modulus of compression......... (a) is independent of temperature of pressure and viscosity (b) increases with the pressure (c) is independent (d) has a dimensionless unit 6. If a non-uniform solid body weighs 500 N in air and when it is completely submerged in water its weighs is 300 N. If it has a volume of 0.0136 m³ then its specific gravity is.......... (c) 2.5 (d) 3.0 (e) none of these (a) 1.5 (b) 1.7 7. A flat plate of area 1.5 m² is pulled with a speed of 0.4 m/s relative to another plate with a distance of 0.15 mm clearance between them. For a fluid viscosity of 0.1 Pa.s, the power required to maintain this speed is (a) 160 W (b) 100 W (c) 200 W (d) 400 W 8. A solid wooden cylinder (SG = 0.6) has diameter of 0.8 m and a height of 3 m, when the cylinder is floating vertically on its base in water then the submerged height of the cylinder is. (a) 1.1 m (b) 1.4 m (c) 1.8 m (d) 2.6 m 9. A wooden cube (SG=0.6), its base 5 cm x 5 cm and has 10 m height, floats vertically…
A cube 2.2 feet on an edge has its lower half of s.g. = 4.8 and upper half of s.g. = 2.9. It rests in a two-layer fluid, with lower sg. = 4.6 and upper s.g. = 3.95. Determine the height, h, of the top of the cube above the interface. See the Figure below. Note: Show step-by-step, and explain each step.
A droplet having a diameter of 0.0762 mm if it is equivalent to an air-water interface giving a surface tension of 0.0730 N/m. a. What is the difference in pressure between the inside and outside of a droplet in N/m²? b. Compute the pressure in kPa. c. Compute the force due to surface tension in N.
Q3. A line CD 80 mm long makes 45° inclination with HP and 30 with VP. End C is 20 mm above the HP and 30 mm infront of the VP. Draw its projections and find its traces.
1.32 A 1.5 in diameter shaft rotates in a sleeve bearing which is 2.5 in long. The radial clearance between (he shaft and the slecve is 0.0015 in, and this is filled with oil having , = 1.$3 x 10-2 lb/ft•s Assuming rotational speed of 62 rpm and a lincar velocity gradient in the lubricating oil, determine the resistive torque due to viscous shear at the shaft-lubricant interface. Ans. 0.0079 ft-lb
The vessel is 20m long, 10m wide and 5 m deep. It has a draft of 4, when floating in an upright position. The center of gravity of the scow is on the axis of the symmetry, Find: (a) The initial metacentric height (at initial position) (b) The metacentric height in tilted position when the vessel is at the point of submergence. (c) The distance between weight and the buoyancy in tilted position. (d) The moment created. (e) Classify the kind of moment. (f) The shifted distance of buoyancy.
Answer this using 7 steps: Given: Required: Assumption: Illustration: Formula: Solution: Answer:
A 4 m long metal cylinder with an external diameter of 600 mm anda wall thickness of 10 mm is filled with water at a pressure of 35 Bar. Young's modulus E = 60 GPa, Poisson's ratio v = 0.3 Calculate the hoop stress, OH, in megapascals (MPa) correct to two decimal places. OH: MPа Calculate the longitudinal stress, L, in megapascals (MPa) correct to two decimal places. OL: MPа Hence, calculate the maximum strain, eH, in the cylinder. Enter your answer in micro-strain correct to two decimal places: EH micro-strain
An underwater pipeline must be laid 40 meters deep. The density of sea water is 1 025 kg/m³. The pipe has a mass of 40 kg per meter and an outside diameter of 300 mm. The pipe must be anchored every 5 m to the bottom of the sea. (a) What will the vertical force be on each anchor if the 4.3 pipe is empty. (b) What external pressure must the pipe be able to withstand if it is not to be crushed. [1 592 N, 402,2 kPa]