1. You run a frequency analysis for a pretensioned beam structure (at one end the beam is compressed). What is the effect of the compression on the natural frequencies of the structure? 2. You run a frequency analysis and you noticed that in the results data some of the eigenvalues are repeated. Please explain in your word when this may happen.

Q: Determine the equation of the influence line for the reaction at A in the continuous beam shown in…

A: By Muller Breslau method, As we have to find the reaction at end A, hence Support at A will be…

Q: Can you add the datum line in the illustration and make a bettter illustration based on solution

A: Given, Angle made by nozzle = 45o Horizontal distance = 15 to 20 m

Q: y 130 mm 30 mm 30 mm -40 mm 40 mm-

A:

Q: x; ]] a» a» dz || X2 a3 a a33

A: For calculation assume,

Q: What is this called?

A: Chisel

Q: Determine the Centroid of 3 Areas.

A:

Q: Define The required diameter

A: A diameter is a chord that runs through centre point of circle. The centre of circle is at midpoint…

Q: Determine number of external indeterminacy

A: Given data : Number of external support reaction (R)=3+3=6 m=Number of member connected at hinge…

Q: 10 + 5x < 6+3x

A:

Q: Compute Ix for the region shown. y 2 18 2-5--5- -2 -8 8. Dimensions in inches

A: The area is divided into the standard areas as shown below.

Q: For the given structures, determine the degree of indeterminacy. 7. A 7

A:

Q: Locate the centroid 10 mm 20 mm 10 mm 10 mm 20 mm 50 mm y

A:

Q: For the given structures, determine the degree of indeterminacy. 8. 8

A: Solution : The number of external reactions ( r ) = 9  The number of members ( n ) = 2  These values…

Q: Find KN derivation Y = K m²³

A: We have to prove that the unit of unit weight is kN/m3.

Q: X 0.75 3 -3.5 1.5 1.5

A:

Q: Give real life examples of Mohr's Circle

A: Brief concept introduction- Mohr's Circle- It gives the relationship between the normal and shear…

Q: A C L- (2) B "1-12- -L/2→ C x

A:

Q: Determine y for the area shown y 1" 1" in .5" 1" 2" 2" X

A:

Q: From the rectangular area shown a semi-circle of radius 4 cm is removed. Locate the centroid, (C),…

A:

Q: * Dount command Creates a filled circle or a filled ring O a filled circle or a wide ring. a wide…

A:

Q: 31⁄5 / 4⁄7

A: 31/5=6.2 4/7=0.571

Q: Differentiate initial and boundary value problems.

A: Both type of problems are similar to each other except for that boundary value problem have…

Q: +y") dx ly

A:

Q: 80 38 24 340 R24 25 R40 130

A: It is not possible that every command and steps that is used in the drawing is to write down here…

Q: Difference betwen Veletile nd frzcead Saled

A:

Q: 38 O 18 22 66 102 The known: front projection, side projection Required: Draw the three projections…

A:

Q: х у The value of |2y + z y [2z + x [2x + y z is

A:

Q: Draw shear force diagram

A:

Q: -0129 -077 R26

A:

Q: For the given structures, determine the degree of indeterminacy. 3. 3

A: The given structure has two fixed supports at ends and one roller support in the middle. The fixed…

Q: geven that 1-front view 2-top view find the 1-side view 2-front section

A: In engineering drawing, a different type of projection is there the isometric projection is the…

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.