1. What is correct about the advantages of shear walls is ( ) A. self-weight of the structure is big B. Small lateral displacement under horizontal load C. High lateral stiffness D. spacing is small E. Flexible plane layout 2. The load-bearing system of 18-storey civil buildings with large space is a priority ( ) A. Framework structure system B. Cylinder structure system C. Frame-shear wall structure system D. Hybrid structural system 3. Among the following building systems, the maximum lateral stiffness is ( ). A. Truss structure system B. tube structure system C. Frame-shear wall structure system D. Hybrid structural system

1. What is correct about the advantages of shear walls is ( ) A. self-weight of the structure is big B. Small lateral displacement under horizontal load C. High lateral stiffness D. spacing is small E. Flexible plane layout 2. The load-bearing system of 18-storey civil buildings with large space is a priority ( ) A. Framework structure system B. Cylinder structure system C. Frame-shear wall structure system D. Hybrid structural system 3. Among the following building systems, the maximum lateral stiffness is ( ). A. Truss structure system B. tube structure system C. Frame-shear wall structure system D. Hybrid structural system

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. The beam shown is prestressed using a bonded (stress relieved tendons) with a specified tensile strength of prestressing tendons fpy = 1350 MPa, and fc' = 35 MPa. The area of prestressed reinforcement in tension zone Aps = 1000 mm². The specified yield strength of prestressing tendons fpy = 1160 MPa. 0.85fc' C a 430 N.A. |(d-a/2) Ap=1000 T=Ap,Sps 250 a. Determine the value of the stress in prestressed reinforcement at nominal strength. b. Determine the value of the depth of the compression block. c. Which of the following gives the ultimate moment capacity of the prestressed beam.
A rectangular beam section is limited to a size of b=250 mm and h=400 mm. Assume that bars in compression will be placed at 60 man from the compression fiber and bars in tension 60 mm from the tension fiber. Given that f'c=21 MPa and fy = 420 MPa 1. Calculate the amount of tension rebars that will have a minimum tensile strain of 0.005 compatible with concrete strain of 0.003 2. If the beam section will be reinforced with tension rebars at a minimum tensile strain of 0.005, calculate the required depth in men of uniform stress block on concrete in compression. 3. With this amount of tension rebars, calculate the design strength of the beam section in kN m. 4. For the beam to sustain a factored moment of 160 kN.m, what will be the required amount of tension steel area in mm² in addition to the tension rebars described in item #1. 5. Considering a doubly reinforced section with tension rebars at a tensile strain of 0.005, calculate the resulting compression stress in MPa…
A rectangular beam has a width of 380 mm, effective depth of 445 mm, and overall depth of 510 mm and is reinforced with four No.29 tension bars. The concrete modulus of rupture fr = 3.65 MPa. The elastic modulus of the concrete and steel are, respectively, Ec =27,800 MPa and Es= 200,000 MPa. Determine if the beam will show hairline cracks due to a bending moment M = 108 kN-m and compute the relevant stresses. Provide material properties for concrete and reinforcing steel used in your design.
Allowable Compressive Stress A structural column Z section having a length of 10 m has an area of 600mm^2, Ix= 120x10^6 mm^4, Iy= 50x10 6 mm^4 and Ixy- -75x10^6 mm^5, Fy - 250 MPa. a) Determine the minimum moment of inertia. b) Determine the maximum moment of inertia. c) Determine the allowable axial stress. d) Determine the factor of safety. .....
Question 1 The T-section beam shown in the figure below is required to resist an ultimate design moment of Mu = 460 kN m. The characteristic materials strengths are fy = 410 N/mm2 and fou 20 N/mm2. Calculate the area of reinforcement required. %3D b = 685mm ht = 90 mm d = 560 mm bw = 300 mm
A reinforced concrete T-Beam has a width of 800mm and a thickness of 50mm. It has an effective depth of 300mm and is reinforced at the bottom with a total steel area of 1800sq.mm. If the web thickness of the T-beam is 200mm, with a concrete strength of fc' = 20MPa and yield strength of steel fy= 400MPa. Assume steel yields. The value of the area subjected tocompressive stress is _sq.mm A. 42,353 sq.mmB. 42,553 sq.mmC. 42,153 sq.mmD. 41,953 sq.mm
A cast iron tube 3m long is completely filled with concrete and used as a vertical strut. if the external diameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressive load the composite strut can support if the stress in the concrete is not exceed 2N/mm2. By how much should the strut shorten under this load. For cat iron EA= 100GN/m? and for concrete Eb = 10GN/m?. %3D
A rectangular reinforced concrete beam has a width of 300 mm and an effective depth of 400 mm. Concrete strength is f’c = 28 MPa and steel yield strength is fy = 280 MPa. a. What is the distance of the neutral axis from the top of the beam so that the strain in the concrete 0.003 will be attained at the same time with the yield strain of steel? b. What is the total compressive force on concrete? c. What is the balanced steel ratio?
1.) Given the following properties of a rectangular concrete beam: b = 280mm, d = 480 mm, f'c = 21 MPa, fy = 414 MPa. The beam is reinforced for tension only. Determine the design strength under the following conditions. a.) When the beam is reinforced with three 25 mm diameter bars. b.) When the beam is reinforced with four 25 mm diameter bars. c.) When the beam is reinforced with seven 25 mm diameter bars.
CASE:A rectangular beam has the dimensions (see Fig.1) b = 15 in.,h = 30 in., and d = 27.37 in. and is reinforced with three No.9 bars. The concrete compressive strength fc' is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel fy is 60,000 psi, the stress-strain curves of the materials being those of Fig.2. Determine the stresses caused by a bending moment M = 45 ft-kips.Question1:Check this case, would the concrete of the beam crack? Please calculate the strengths of those two materials in this beam.Question2:Suppose the beam under this case is subject to a bending moment M = 110 ft-kips (rather than45ft-kips as previously). Calculate the relevant properties and stresses.Question3:Determine the nominal moment Mn at which the beam of this case will fail. Question4:Have a comparison of the calculation results with those of three questions.
A cast iron 3m long is completely filled with concrete and used as a vertical strut. If the externaldiameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressiveload the composite strut can support if the stress in the concrete is not 2N/mm2? By how muchshould the strut shorten under this load? For cast iron EA= 100GN/m2 and for the concrete EB=10GN/m2?
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As