1 and 2 1. Using Superposition theorem, solve for current Iww12VO2A2. Determine the load currents at 2 0, 14 0, 40 and 100 0 using Superposition theorem.ww2035ATOGv

As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again.

Answered: 1. Using Superposition theorem, solve…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 4PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and current relationships change? (a) If C1 is the complex positive-sequence voltage gain in Problem 3.29 and (b) if C2 is the negative sequence complex voltage gain, express the relationship between C1andC2
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
Q22222222222 aaaaaaaaaaaaaaaa
i need the answer quickly
Q2) Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). Volvolt) 2- The ripple voltage. Vm = 12 V 3- The Vdc value. 4- The RMS value of the output voltage. V(p-P) = 0.1 V 5- The ripple factor. 6- The value of capacitor filter. (assume ideal diodes) T= 0.01 sec. t(sec.)
I need the answer at 20 minute
Determine the branch currents Is, Igandl, in ampere. TVⒸ so www 14 Eng al. The current in ampere 11 [Select] b). The current in ampere 12 [Select] 60 www d. The current in ampere 13 [Select] 40
Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).
Q2) Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). VOlvolt) 2- The ripple voltage. Vm = 12 V 3- The Vdc value. 4- The RMS value of the output voltage. V(p.P) = 0.1 V 5- The ripple factor. 6- The value of capacitor filter. (assume ideal diodes) T = 0.01 sec. → t(sec.)
A generator rated at 30MVA, 11kV has a reactance of 40%. Calculate its p.u. reactances for a base of 50MVA and 10kV. O 0.606 p.u. O 0.506 p.u. O 0.806 p.u. O 0.706 p.u.
Vs=16cos100t Volt using T-equivalent circuit for For the circuit shown, find the steady-state 102 voltage "V" and the input power when 100 0.11I V=16cos100t Volt using T-equivalent circuit for transformer. 0.21I 0.211: 50 (Ans.: V=6cos100t Volt & Pin=11.2W)
What effects are produced by change in voltage? 1. Iron los..........varies approximately as V². 2. Cu loss..........it also varies as V² but decreases with an increase in voltage if constant kVA output is assumed. 3. Efficiency...........for distribution transformers, efficiency at fractional loads decreases with in- crease in voltage while at full load or overload it increases with increase in voltage and vice- versa. 4. Regulation..........it varies as but decreases with increase in voltage if constant kVA output is assumed. 5. Heating.........for constant kVA output, iron temperatures increase whereas Cu temperatures decrease with increase in voltages and vice-versa.

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

1. Using Superposition theorem, solve for current I ww