1. Using Kirchhoff's Laws, determine all the branch currents in the two circuit diagrar 20 60 (a) 12 14 30 ) 0.5 A 30 5V 10 V 230 v 35 S2 355L Is (b) 210 V 25 sv 210 Vt 152 15 I4 25 L

Q: What does the following code do? LDA 1000H MOV B, A LDA 2000H STA 1000H MOV A, B STA 2000H Loads the…

A: INSTRUCTION SET BASED ON OPERATION MODES: Data transfer (Copy) instructions set: In this group, the…

Q: Here are 4 EEPROM memory system. What addresses are associated with each of the 4 memory chips.

A: According to the question, for the given combination of EEPROM as shown below We need to calculate…

Q: QUESTION 4 The following code is used as delay in a program: 0104 MOV BX, 0004 0107 MOV CX, FFFF.…

A: The address of the BX=0008H instead of 0004H.  When the loop is ON,  DEC is used here for…

Q: What can you determine about the circuit being tested based on what is displayed on the DMM?

A: Circuit shows three lamps, dome lamp, Lamp A and Lamp B are  connected in parallel and supplied…

Q: Question 1 You have a supply of 8K x 4 memory chips. The address bus on each chip will be. (Type out…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: Requirements You are required to create a functioning circuit that models some of the basic features…

A: According to the question, we need to design a circuit diagram based on the given conditions,…

Q: please dont use AI, it gives wrong answer thank u. solve by hand and i will like

A: Question i. a. If the ARM processor is configured as little-endian, it means that the least…

Q: Sensors are used to monitor the pressure and the temperature of a c at. The circuitry for each…

A:

Q: Write a program in 8051 to copy the contents of code ROM addresses 0100H-0102H to internal RAM…

A: In the program microcontroller require to copy the contents from ROM address 0100H-0102H and store…

Q: Find the number of digits required when converting the number (743)10 to octal number(show all your…

A:

Q: 1.12 (a) Convert to base 3:375.54g (do all of the arithmetic in decimal). (b) Convert to base 4:…

A:

Q: Sometimes light fixtures are controlled by more than one switch. Circuits need to be designed so…

A: According to the question, we need to design a circuit in which light fixtures are controlled by…

Q: 2. Refer to the graphics appendix. What current is most near the current through R2? .200 A .046 A…

A:

Q: The Figure shown • Write the truth table • Minimize use map entered variable method when C is…

A:

Q: L1 Inputs o-S1 OPL2 OPL3 O PL4 0-S2 00-S3 0-S4 0-S5 S1 36 S2 E S3 JE Ladder logic program Main…

A: The given ladder logic circuit is shown below. It is mentioned to assume all the switches are…

Q: able 1 Resistance pins 1-2 Resistance pins 2-3 Total resistance (R1-2 +R2-3) Step 2 0.960KQ 0.10…

A:

Q: Which of the following is true of the following circuit (Check all that apply). a -f It contains a…

A:

Q: What is the equivalent resistor, in units of Ohm, between the terminals a and b if you replace R1 by…

A: For this problem first we have to convert star into delta. Then easily found equivalent resistance.

Q: need help solving this so i can get an idea of how to do other ones

A: The solution can be achieved as.

Rectangular Coordinate System

In a rectangular coordinate system, each point based on the pair of coordinates is specified uniquely in the plane. From two fixed perpendicular lines, these coordinates are at a distance in the rectangular coordinate system. Each line is known as the reference axis and axes as plural. The point where they meet is called the origin (0,0).