1. Using Block Diagram Reduction technique find closed loop transferfunction of the system whose block diagram shown belowG₁G₁RESULTG₂H₁H₁The overall transfer function is given by,CG,G₂G3+G,G4R 1+G₁G₂H, +G₂G₂H₂ +G₂H₂ +G₁G₂G3 +G₁G₁

Answered: Image /qna-images/answer/c84ddb31-fcdb-4fd2-8e8a-15925d8d906a.jpg

1. Using Block Diagram Reduction technique find closed loop transfer function of the system whose block diagram shown below G₁ R G₁ G₁ G₁ H₁ H₁ The overall transfer function is given by, C G,G₂G,+G,G R 1+G,G₂H, +G₂G₂H₂ +G₂H₂ +G₁G₂G₂ +G₁G₁ RESULT

1. Using Block Diagram Reduction technique find closed loop transfer function of the system whose block diagram shown below G₁ R G₁ G₁ G₁ H₁ H₁ The overall transfer function is given by, C G,G₂G,+G,G R 1+G,G₂H, +G₂G₂H₂ +G₂H₂ +G₁G₂G₂ +G₁G₁ RESULT

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the system shown in Figure 2, suppose that R(s) is the reference input signal and the D(s) is the disturbance input signal, with K and K, to be decided. D(s) R(s) E(s) u1(s) (s) Y(s) --2z + 2u K K Figure 2: 1 1). Find the closed-loop transfer functions G1(s) and G2(s) in E(s) = G1(s)R(s) + G2(s)D(s). 2). What are the damping ratio ( and natural frequency wn of this system ? Discuss the impact of K and K, on ç and wn. 3). Discuss the impact of K and K, on the tracking error e(0) for a unit-ramp reference signal and a unit-step disturbance signal.
B + vo loudspeaker is an electromechanical system that can be modeled by the electric Circuit and the mechanical system shown in Figure The voltage ed in the electric circuit is proportional to the speed of the mass, ie. K₁, and the force f acting on the mass is proportional to the current 4, Le.. - Kat. Find the transfer function from the input voltage v, to the mass position r, in terms of the parameters R, L, M, b. K₁, and K₂. 1x R ww e coil f- Figure Problem. M TH
B + va loudspeaker is an electromechanical system that can be modeled by the electric circuit and the mechanical system shown in Figure. The voltage cod in the electric circuit is proportional to the speed of the mass, ie.. Cont Kit, and the force / acting on the mass is proportional to the current 4, 1e., - Kat. Find the transfer function from the input voltage v, to the mass position a, in terms of the parameters R, L, M, b. K₁, and K₂. R ww + Coil f- Figure Problem. M x TH
Do c i) and ii)
2. Find the transfer function of the signal flow graph shown in figure? R(s) G₁(s) G₂(s) V4(s) I H₁(s) G3(s) Gg(s) V3(s) V₂(s) G7(s) G4(s) H4(s) H₂(s) Vs(s) please answer in typing format Gg(s) V₁(s) Figure 2: Problem 2 Signal flow graph G6(s) O C(s)
Feedback Control 1
1 of 1 Discuss the process of Nyquist Criterion as applied to open-loop function. В I Σ II II ... DI II
I need the answer as soon as possible
For the electric circuit given in the figure;a) Obtain the transfer function between V2(s) and V1(s).b) Calculate the gain value and time constant of the system in steady state as C=2MicroFarad, R1=R2=1Mohm.c) According to the values given in option B, obtain the expression to be obtained at the output for the unit step input by using the residual sum method.
Given G₁ = 4(s+8) /(s+3)(s+7) and G₂=2s /(s+10) function write an m-script to determine the final transfer i. Series ii. Parallel iii. Feedback, taking G₂ as the feedback element
3. In this problem, use the two closed loop systems given in the figure to answer the questions below. 4 R(s) K₁ 0.0099 In thin K₂ Y(s) R(s) K₁ 4 S(s) = 0.09 K₂ 0.09 (a) Show that these two systems have the same transfer function for K₁ = K₂ = 100 (b) Using the definition of sensitivity, S(s), for each system calculate the sensitivity to the parameter K₁ with K₁ and K₂ as variables. Recall: Y(s) OG G OG Gal (c) Substitute K₁ = K₂ = 100 into each S(s) and compare the sensitivities to parameter K₁.
Pls do this question correctly and neatly and don't copy from anyone, if I get to know then it won't be good for you pls do on your own