1. Two solid shafts of different materials are rigidly fastened together and attached to rigid supports as shown. The aluminum segment is 3 inches in diameter and G = 4 x 10^6 psi. The steel segment has a diameter of 2 inches and G = 12 x 10^6 psi. The torque, T = 10 kips.in. is applied at the junction of the two segments. Compute the maximum shearing stress developed in the assembly.

1. Two solid shafts of different materials are rigidly fastened together and attached to rigid supports as shown. The aluminum segment is 3 inches in diameter and G = 4 x 10^6 psi. The steel segment has a diameter of 2 inches and G = 12 x 10^6 psi. The torque, T = 10 kips.in. is applied at the junction of the two segments. Compute the maximum shearing stress developed in the assembly.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

b) Using the method of joints, find the force in each member and state whether 100 Ib each is in tension (T) or compression (C). FAB - 350 1b (c) FAF = 71.416 (T) Fec • 233. 5 olc) Fer - u2. a (t) Fco - 371.1 la (c) fot n2.7 lo (T) FLE 300 (T) 200 6 300 1b
Q2. Given: f'c= 28MPa fy= 420MPa Section: rectangle: b= h= 500mm Loads: Pu= 3833kN Mu= 300kN.m Determine the required area of longitudinal steel needed to resist these loads. IS 456
Determine the forces in members using the method of section FE, LK, and LG. Include your complete solution along with its free body diagram.
35. For the beam loading of Figure P3-34, design the beam choosing a commercially available shape in standard SI units from Appendix 15 with the smallest cross-sectional area that will limit the bending stress to 100 MPa. R₂ 800 N -0.81 400 N 600 N --0.3 m--03 m--04m- B C |9.3m-22- 200 N
A built-up wooden beam section is made of two 58 mm x 104 mm sections glued on the lower sides of a 58mm x2(104) mm section as shown. a) Solve for the total area (mm2) of the beam section b)Determine the distance of the centroid (mm) from the top section of the beam. c) Determine the distance of the centroid (mm) from the bottom section of the beam
es Refer the beam shown with cross section of thickness, t = 15 mm. If F = 84 kN and a = 150 mm, F F 2a -40a Find the section modulus of the cross section. Select the correct response: 11946.67 mm³ Ⓒ14400 mm³ 12000 mm³ 12800 mm³ 1 2a t
Draw the FBD an determine the reactionsof the beam.
1) Consider the elevation view of an interior beam shown below. The beam has a t-shaped cross- section (the 5 in. thick slab is cast monolithically with the beam - meaning that the 22 in. deep beam has 17 in. hanging below the slab). The c-c length is 30 ft. Assume: M bw = 14 in. fc = 6 ksi Mu,neg. = 340 k.ft en = 28.5 ft Wu h = 22 in. fy = 60 ksi Mu,pos = 230 k.ft Sw = 12 ft - Length hstab = 5 in. No. 4 stirrups Column FL a. Select flexural reinforcement for the beam at midspan assuming it is singly reinforced. T- beams under positive bending are usually singly reinforced because the depth of the neutral axis in the flange is often smaller than the depth of any bars that might be present. Iterate until the design strength, Mn, exceeds M₁ by less than approximately 20%. Provide a drawing of the section design that clearly shows the location of the longitudinal reinforcement. Show the section complies with relevant ACI Building Code requirements (As,min, bar spacing limits, Et, min). b.…
6. 20ft P= 20K Mmax CA A max =
Draw the FBD of member ADB
Mechanics of deformable bodies
Please help me please.