1. The timber columns that support the beam have the dimensions 600mm x 800mm x 3m. The angle of the grain is shown in the figure below. Compute the bearing stress between the grains of the column at Point H.

1. The timber columns that support the beam have the dimensions 600mm x 800mm x 3m. The angle of the grain is shown in the figure below. Compute the bearing stress between the grains of the column at Point H.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
Three plates are welded together to form the section shown. Dimensions of the cross section are b= 4.7 in., d = 14.1 in., a = 2.8 in., and t= 0.5 in. For a vertical shear force of V = 42 kips, determine the shear flow through the welded surface at B. B a b Answer: kip/in.
A small aluminum alloy [E = 80 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P ЗР Strain gage d D E H Answer: P = i
6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
A square beam (w=0.03 m) is loaded with a point load of 1000 N and a moment load of 1000 Nm, as shown. i. Determine maximum deflection of the beam using step by step analytical equations. ii. Determine the Maximum stress in the beam using step by step analytical equations iii. For both top fibers and bottom fibers of the square beam, specify the type of the stresses.
A small aluminum alloy [E= 77 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape are b= 22 mm, d = 33 mm, and t= 4 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 uɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? %3D %3D %3D 3P Strain gage E Answer:
4.15 Knowing that for the casting shown in the figure the allowable stress is 6 ksi in tension and 15 ksi in compression, determine the maximum couple M that can be applied.
2. (3 points) When loading is applied at a point on a body, the stress distributions at different cross sections are different. However, the stress distribution becomes uniform at locations far from the applied load. This is due to which principle? Name the principle. P Load distorts lines located near load P P C C Lines located away from the load and support remain straight P O avg A section a-a section b-b section c-c -Load distorts lines located near support Your answer
A rectangular plate is subjected to uniform biaxial stress with x = 90 MPa (tension), oy = -20 MPa (compression), and ₂ = 0. The plate has original dimensions 400 X 800 X 200 mm (x X y X z) and is made of steel with E = 200 GPa and v = 0.3. What are the strains Ex, Ey, and Ez?
A steel rectangular block is subjected to a uniform stress of o = 150 MPa acting on all faces. The dimensions of the block are as follows: L_x=100 mm,L_y=30 mm,L_z=40 mm. Determine the change in length along the y-axis. Use E = 200 GPa and v 0.3. Note that ɛ_0=-o/E(1+2v). A -0.03 mm -0.015 mm -0.009 mm -0.012 mm
For the cross-section shown below, determine the maximum amount of tension reinforcement (A.) so that the beam cross-section is tension-controlled. [hint: use the strain diagram shown below]. Use fy = 60 ksi and fe=4 ksi. b=12 in. E, = 0.003 †d'= 2.5 in A' =2#9 n.a. d=17.5 in A = ? E, = 0.005