1. The stress induced in a body when subjected to two equal and opposite pulls is known as: (a) Compressive stress (b) Shear stress (e) Tensile stress (d). 2. The force of resistance per unit area offered by a body against deformation is known as: (a) Resistance (b) Stress (c) Strain (d)... 3. If the external force acts on a body is removed and the body comes back to its origin shape and size, the body is known as : (a) Plastic body (b) Elastic body (c) Ductile body (d) 4. The ratio of change of dimension of the body to the original dimension is known as: (a) Strain (b) Deformation (e) Simple stress (d).

1. The stress induced in a body when subjected to two equal and opposite pulls is known as: (a) Compressive stress (b) Shear stress (e) Tensile stress (d). 2. The force of resistance per unit area offered by a body against deformation is known as: (a) Resistance (b) Stress (c) Strain (d)... 3. If the external force acts on a body is removed and the body comes back to its origin shape and size, the body is known as : (a) Plastic body (b) Elastic body (c) Ductile body (d) 4. The ratio of change of dimension of the body to the original dimension is known as: (a) Strain (b) Deformation (e) Simple stress (d).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Three wires experience the same deformation ō. Which wire will experience the smallest normal strain? O a 10-inch-long wire O a 10-mile-long wire O a 10-foot-long wire
Please i need the answer i have an exam now quickly please
3.
1.26 part C thanks
In a structure subjected to fatigue loading, the minimum and maximum stresses developed in a cycle are 200 MPa and 400 MPa respectively. The value of stress amplitude (in MPa) is
1. A 1.5-m long circular cross-sectioned bar with r = 1 cm is under a combination of bending moment of 70 N-m and torque of 50 N-m. Determine (a) the location of the critical point on the bar. (b) the resulting normal stress at the critical point. 6 (c) the resulting shear stress at the critical point. T ) "P (d) the principal stresses, principal direction, and maximum shear stress at the critical point. 6₁,2 (e) Draw a Mohr's circle representing the state of stress at the critical point. 1.5 m M = 70 N-m T = 50 N-m
As shown on the right, two circular rods (CE and DF) are attached to a rigid bar (ABCD). Knowing that 2 m 1m 3 m the diameters of the rods are: der = 10 cm dor = 20 cm the young's moduli of the rods are ECE = 200 GPa Epr = 80 GPa 4 m 5 m 10KN Determine the forces applied by the two rods, i.e., Fce and For
A cylindrical bar of metal having a diameter of 20.0 mm and a length of 190 mm is deformed elastically in tension with a force of 50800 N. Given that the elastic modulus and Poisson's ratio of the metal are 61.4 GPa and 0.34, respectively, determine the following: (a) The amount by which this specimen will elongate in the direction of the applied stress. (b) The change in diameter of the specimen. Indicate an increase in diameter with a positive number and a decrease with a negative number.
H.W.8 When an axial load is applied to the ends of the two- segment rod shown in Figure P2.1, the total elongation between joints A and C is 7.5 mm. The segment lengths are a = 1.2 m and b=2.8 m. In segment (2), the normal strain is measured as 2,075 µm/m. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the rod. (1) P В C b FIGURE P2.1 (2)
Soil mechanics
Mechanics of deformable bodies
Mechanics of material