1. The electric voltage, V(t) = 150 + 75 sin(20nt) [mV], is going to be observed on the oscilloscope. The oscilloscope display has 10 vertical blocks and 10 horizontal blocks. The oscilloscope parameter is DC-coupling and the vertical position is 0. The choice of volt/div parameter is 10, 25, 50, 100, and 200 [mV/div]. Choose the optimum value for volt/div parameter! Give your reason. (optimum = the signal isn't too big until it is out of the display and also the signal isn't too small to see) The voltage signal is going to be observed in 5 periods. Calculate the time/div parameter. Based on the initial parameters and the parameters selected in Question a) and b), sketch the voltage signal displayed on the oscilloscope! If the coupling is changed to AC coupling, calculate the average and RMS value of V(t)! a. b. C. d.

1. The electric voltage, V(t) = 150 + 75 sin(20nt) [mV], is going to be observed on the oscilloscope. The oscilloscope display has 10 vertical blocks and 10 horizontal blocks. The oscilloscope parameter is DC-coupling and the vertical position is 0. The choice of volt/div parameter is 10, 25, 50, 100, and 200 [mV/div]. Choose the optimum value for volt/div parameter! Give your reason. (optimum = the signal isn't too big until it is out of the display and also the signal isn't too small to see) The voltage signal is going to be observed in 5 periods. Calculate the time/div parameter. Based on the initial parameters and the parameters selected in Question a) and b), sketch the voltage signal displayed on the oscilloscope! If the coupling is changed to AC coupling, calculate the average and RMS value of V(t)! a. b. C. d.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 2ms/cm and the volt/cm switch on 4 V/cm. The width of each complete cycle is 6.8 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.8 cm and 5.3 cm respectively. The difference between the two waveforms is 0.5. Determine a) frequency; b) phase difference, C) RMS value of G waveform d) peak value of H waveform a) frequency b) phase difference C) RMS value of G waveform d)peak value of H waveform (8)
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 50 ms/cm and the volt/cm switch on 6 V/cm. The width of each complete cycle is 5.3 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.6 cm and 5.9 cm respectively. The difference between the two waveforms is 0.7. Determine a) Frequency b) Phase difference c) RMS value of G waveform d) Peak value of H waveform a) frequency
A double beam oscilloscope displays 2 sine waveforms A and B. The time/cm switch is on 150µs/cm and the volt/cm switch on 5 V/cm. The width of each complete cycle is 8 cm for both the waveforms. The height of waveforms A and B are 5 cm and 4 cm respectively. Determine their a) frequency, b) phase difference, and c) peak and d) r.m.s value of voltages. The difference between the two waveforms is 0.7 cm.
i need the answer quickly
where to put the oscilloscope probes in this circuit to see the output waveform? (main hook and ground hook)
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 45 ms/cm and the volt/cm switch on 5V/cm. The width of each complete cycle is 6.8 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.6 cm and 4.9 cm respectively. The difference between the two waveforms is 0.9. Determine a) frequency, b) phase difference, c) peak value of H waveform. d) RMS value of G waveform a) frequency b) phase difference C) Peak value of H waveform d) RMS value of G waveform
In a circuit where the total voltage is defined by 200sin (300t + 45degrees) V, what is the period of this waveform?
i need the answer quickly
The time/div and voltage/div axes of an oscilloscope have been erased. A student connects a 1 kHz, 5 V P-P square wave calibration pulse to channel-1 of the scope and observes the screen to be as shown in the upper trace of the figure. An unknown signal is connected to channel-2 (lower trace) of the scope. If the time/div and V/div on both channels are the same, the amplitude (p - p) and period of the unknown signal are respectively
Determine Voand Sketch output waveform for the clamper network shown. 20 V + Si + R Vo Vi 4 V- -20 V