1. The cart in the figure (and in the video: https://youtu.be/gvPNrdfNo9g ) is attached to a lightspring that can stretch and compress equally well. The cart and spring rest on a low-frictionhorizontal surface. The cart is shown at position III, at rest, not accelerating. The cart is pulled toposition I (stretching the spring) and then released. It moves to position V, where it then reversesdirection and returns again to position I. It repeats the motion.IVII Draw a force diagramDraw a forceDraw a force diagram Draw a forcefor the cart while it is atdiagram for point III, for point V, cartdiagram for point II,point Land moving left.cart moving left.moving left.cart moving left.Draw a force diagram Draw a forceDraw a force diagramfor point I, cart movingDraw a forcediagram for point III, for point V, cartmoving right.diagram for point II,cart moving right.right.cart moving right.

Answered: Image /qna-images/answer/c0fdaa37-9981-4ef3-9d5c-c8855d9e0d3d.jpg

Answered: 1. The cart in the figure (and in the…

Similar questions

An ornament of mass 40.6 g is attached to a vertical ideal spring with a force constant (spring constant) of 45.6 N/m. The ornament is then lowered very slowly until the spring stops stretching. How much does the spring stretch?
A box is motionless, sitting on a ramp with an incline of 0 =54.4 ° being pulled in the direction up the ramp by a spring with a spring constant of k=150 N/m that is stretched x=6.4 m. The coefficient of friction between the ramp and the box are u s=0.53 and u k=0.15 and the friction force is going down the ramp. What is the mass of the box? Solve symbolically: Solve numerically: m= Units: If the box starts moving up a ramp with an acceleration of a=2.41 m/s, what is the new length that the spring will stretch? Solve symbolically: Solve numerically: Units:
2. Maria and Rory are using a spring launcher to move a 125 g block to the top of a ramp. The spring launcher is at the base of the ramp and consists of a platform and a spring with a force constant of 420 N/m. The horizontal surface at the base of the ramp is smooth and frictionless. They compress the spring by 0.12 m with the block resting against the spring launcher. Once they let go, the block travels up the 1.4 m ramp and comes to rest at the top of the ramp. The top of the ramp is 1.0 m above the ground. Ramp Experiment Ad= 1.4 m smooth frictionless surface What is the average frictional force acting on the block as it moves up the ramp? Ah=1.0 m
1. Consider the setup shown below: a block with mass m; sits on a table with friction coefficient u between the table and itself, attached on one side to a spring with stiffness k, and on the other side to a cord with negligible mass that wraps over a frictionless pully and supports a second block with mass m2 that's suspended in the air over the edge of the table. The friction between block 1 and the table is not enough to hold up block 2 so that, when it's released from rest, the spring stretches a distance Ax before the system comes to rest. a. Draw and label a free-body diagram for each block. (Use the gridlines to make sure that the relative lengths of your vector arrows are correct.) k m1 block 1: block 2: m2 b. What is the kinetic friction coefficient between block 1 and the table?
5. Two 8.5 kg masses are hung from a horizontal surface by two (massless) springs, as shown in the figure. The top spring has a spring constant of 400 N/m, and the bottom spring has a spring constant of 200 N/m. How long is each spring in this configuration if they both have rest lengths of 6.0 cm?
3. Before: mi vi After: m2 Ax (mm) I coul m₁+m2 a) Measurements on a spring reveal that a force of 0.75 N will compress the spring by 0.25 cm. Find the spring constant of this spring, k. b) This spring is now mounted horizontally with a block of wood attached to one end. A bullet with mass m₁=0.008 kg and velocity v, is fired horizontally into the block of wood. The wood block has mass m₂=0.992 kg and is initially at rest. The bullet embeds itself in the wood and the spring is compressed by 2 cm before it comes to rest momentarily. c) Find the velocity of the block/bullet combination directly after the collision needed to compress this spring by Ax=2 cm. d) Find the initial velocity of the bullet before the collision, V₁. Hint: Is the collision elastic or inelastic?
Please Asap
1. Blocks A and B move along frictionless vertical bars and are connected with a rope that wraps around the frictionless pulley at P. Block A has a mass of 2kg and block B has a mass of 10 kg. The spring shown is unstretched when block B is in contact with the ground. The system is released from rest in the position shown. Determine the speeds of A and B immediately before B hits the ground. Neglect the mass of the rope and the pulley. The linear spring has a stiffness of 40 N/m and is attached to the ground and to block B. Treat bloeks as particl es with negligible dimensions d = 2.5 m D P 1 = 4m k I h = 2 m A
QUESTION 9 A 10-kg block is attached to one end of a horizontal spring on a level, frictionless surface. The other end of the spring is attached to a vertical support. The spring obeys Hooke's law and has a spring constant of k = 160 N/m. A physics student pulls the block outward so that the spring stretches by 40 cm. The student releases the block at time t = 0.00 s. Which of the following equations properly gives the position as a function of time? a. x(t) = (- 1.6 m/s)sin(4.0t) b. x(t) = (- 6.4 m/s2)cos(4.0t) C. x(t) = (10 m)cos(4.0t) d. x(t) = (0.40 m)cos(4.0t) e. x(t) = (4.0 m)cos(0.40t)