1. Suppose an amplifier has an open-loop voltage gain of 20, an input impedance of 1002, and an output impedance of 502. The amplifier is driven with a sine- wave generator with output impedance of 502 and an open loop amplitude of 0.1 Vpp. Find the resulting voltage across a 2002 load attached to the amplifier output.

1. Suppose an amplifier has an open-loop voltage gain of 20, an input impedance of 1002, and an output impedance of 502. The amplifier is driven with a sine- wave generator with output impedance of 502 and an open loop amplitude of 0.1 Vpp. Find the resulting voltage across a 2002 load attached to the amplifier output.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

d. For the feedback amplifier,. determine the base, emitter, and collector voltages of each transistor. 12 V 220 2 P-80 -160 1.8 MA
2. How the characteristics of the voltage follower (i.e., the high input and low output impedance) affect the voltage appearing across the load resistor? Support your answer using analytical analysis.
Tell the ideal char. of op-amp.
3G Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. Determine the output voltage of the second stage stage. a.-2640 mV b.-26.4 mV c.-1.2 mV d.26 V
Determine the maximum theoretical efficiency of RC-coupled class-A amplifier as shown in Figure Q2(a). Show every detail of the calculation steps. Vcc Ice R1 RL C2 IB R2 IE Figure Q2(a)
3. Amplifier: (a) Which type of amplifier is shown in the figure on the right? What are its proper- ties? What is the condition for U? Name one pratical application for this type of amplifier. (b) Calculate the input impedance of the am- plifier shown in the figure. U R
3A Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. 3H Determine the total gain of the circuit in Problem No. 1 (P1) a.792.105 b.9000 c.792 V d.792
Given the four statements, which of the following statements are not true about the operation of an op-amp? i. Op-amp's close loop operation employs negative feedback that takes portion of the output and applies it back out of phase with the input. 1i. In an op-amp, amplification of the common input signals is much less than that of the opposite input signals. iii. In open-loop operation, the output of the op-amp is driven to saturation with Vo- +Vsat. iv. Op-amp's close loop operation employs positive feedback that takes portion of the output and applies it back out of phase with the input. O i, iii, iv O i, iv O i i, ii O i, iv
QUESTION 2 A non-inverting amplifier has a 15-k Rf and a 1.2-kR,. How much is its closed-loop volt 9. 12.5. -12.5. 13.5.
Operational Amplifier (Op-Amp) is a solid-state device with voltage amplification capabilities as shown in Figure Q1. (a) Name the function of Op-Amp U1, U2 and U3 in Figure Q1. (b) Derive the output voltage (Vol, Voz and Vo3) of each Op-Amp in Figure Q1. Based on derivation in Q1(b), calculate the output voltages (Vol, Vo2 and Vo3) of the circuit. All the Op-Amps are powered with + 12V voltage supplies. Given: Ra = Rb = 1 kN, Ry = Rx = 10 kN, Ra = 3.6 kN, Rr = 3 k2. The input voltages: V,= V = 5 V. (c) (d) Draw and label clearly the sinusoidal output of Vo1, Vo2 and Vo3.
Analog Electronic (Field-Effect Transistors) a) Name the transistor used and plot the transfer characteristics of the transistor. b) Determine the operating point of the amplifier by finding IDQ and VGSQ using the graphical method.