i need the answer quickly تة مر1. In a parallel communication, each bit requires a transmitter and receiver.a) Trueb) False2. What is the cable that carries the information in parallel transmissioncalled?a) Parallel lineb) Data busc) Data lined) Data link3. Which of the following is a false reason for parallel lines not being used forlong distances?a) Cost factorb) Signal Attenuationc) Number of transmission channelsd) Low speed,4. Why higher speed communications in parallel transmission require shorterlength?a) Costb) Resistancec) Inductive and capacitance effectsd) Noise5. Which bit is transmitted first in a serial communication?a) Least significant bitb) Most significantc) All the bits simultaneouslyd) Not in any specific order6. In serial communication, if the time interval to transmit one bit is 10us.What is the time to transmit an'8-bit word?a) 8usb) 80usc) 0.8µsd) 0.008µs

Note :- As per guidelines we are supposed to answer only 3 questions. So I request you to please…

1. In a parallel communication, each bit requires a transmitter and receiver. a) True b) False 2. What is the cable that carries the information in parallel transmission called? a) Parallel line b) Data bus c) Data line d) Data link 3. Which of the following is a false reason for parallel lines not being used for long distances? a) Cost factor b) Signal Attenuation c) Number of transmission channels d) Low speed.

1. In a parallel communication, each bit requires a transmitter and receiver. a) True b) False 2. What is the cable that carries the information in parallel transmission called? a) Parallel line b) Data bus c) Data line d) Data link 3. Which of the following is a false reason for parallel lines not being used for long distances? a) Cost factor b) Signal Attenuation c) Number of transmission channels d) Low speed.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The is the distance from-1 the centre of one slot to the centre of .the next slot a) coil span O b) pole pitch O c) slot pitch O
Give information regarding the Heading Indicator. >History >Development and Timeline>Application >How it works>Regulations
For the following switch circuit: A) Derive the switching algebra expression that corresponds one to one with the switch circuit. B) Derive an equivalent switch circuit with a structure consisting of a parallel connection of groups of switches connected in series. (Use 8 switches.) C) Derive an equivalent switch circuit with a structure consisting of a series connection of groups of switches connected in parallel. (Use 7 switches.)
b) Remove the following complements using DeMorgan's theorems. ______________________ ___________________ _____________ P+ Q + (C+D.E'). (F+G) Please write the solution handwriting.
Choose the correct answer and show your solution. *Kindly provide a COMPLETE and CLEAR solution* (Answer should be typewritten) *Please answer it ASAP if you can
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
I need the answer as soon as possible
22surse_assessment_id=_18982_1&course_id=_22058_1&content_id= _262244_1&ques * Question Completion Status > A Moving to another question will save this response. uestion 2 If the switch is closed for a long time and then opened at t-0. What is the initial value of the capacitor's voltage? ww None of the answers o 12 O Take Test: Quiz 2-. FUJITSU F10 F11 F12 Prt Scr E7 F8 F9 F6 Sys Rq ECO 7 V 8 A 9. 5 Y ! U P
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
17- The electromechanical breakdown depend on the type of the dielectric between two electrodes a- Right. b- Wrong 18- Basic Insulation Level (BIL) is related to the design consideration of the electric device, while Basic protection (BPL) level is related to protection level of the that device. a Right. Wrong. b- 19- As the voltage regulation increased, receiving end voltage will be reduced. Right. b- Wrong 20- We can be using Solar power generation field as a power factor and voltage profile enhancement in Distribution system. (aRight. b- Wrong. 21- From the general electrostatic theories, the field strength at breakdown is given by: a Eb = V/ do =0.6 [Y/ (€ o Er) ] 0.5. b- Eb V/ do = 0.6 [Y / (€ 0/Er )] 0.5. C- Eb V/ do = 0.6 [ Y/(Eo Er) 20.05. d- Eb V/ do = 0.6 [ Y/ (Eo Er) 10.5. 22- Consider plane electrodes with a solid insulator between them. Find the electric field strength at breakdown, if Young's modulus = 10000 (V.F/m2). and the relative permittivity is (36000 TT). If the…
I need the complete solution & explanation pls