1. If the initial velocity of a projectile is given by the equation V. = R. 2h find the initial velocity given the following data, the range R = 1.5m +0.1m, the gravitational acceleration is a constant g = 9.8m/s², and the height of the launch wash and uncertainty. 1m±0.01m. Show all of your work to find the partial derivatives %3D

1. If the initial velocity of a projectile is given by the equation V. = R. 2h find the initial velocity given the following data, the range R = 1.5m +0.1m, the gravitational acceleration is a constant g = 9.8m/s², and the height of the launch wash and uncertainty. 1m±0.01m. Show all of your work to find the partial derivatives %3D

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

B. Solve and graph the following problems. 1. You found a treasure map and it said: Start at the well, go 100m straight south, then 30m 40° north of west, then 25m straight east, and finally 45m, 75° south of east. Using the Polygon Method, how far from the well and in what direction is the hidden treasure?
really need asap
. which of the following statements regarding a positive relative projection height is true? a. the time to the peak heaight will be greater than the time down from the peak height b. the projection angle will be the same as the angle upon landing c. the tme to the peak height will be less than the time down form the peak height d. none of the other staments are true. e. the time to the peak height will be equal to the time down form the peak height
A student stands at the edge of a cliff and throws a stone horizontally over the edge with a speed of vo = 20.5 m/s. The cliff is h = 26.0 m above a flat, horizontal beach as shown in the figure.
dy b) Solve (1 + t?) + y = etan-1t. dt
Fill up the blanks
Show your step by step solutions. 6. With a wooden ruler, you measure the length of a rectangular piece of sheet metal to be 16 mm. With micrometer calipers, you measure the width of the rectangle to be 5.98 mm. Consider 4 significant figures only. Determine: (a) the area of the rectangle; (b) the ratio of the rectangle's width to its length; (c) the perimeter of the rectangle;
Find the resultant of the following vectors using the analytical method Vector A: 7m/s, 0° Vector B: 6m/s, 30° Vector C: 4m/s, 135°
What's this?
3:38 D 1 PI 44 B/s WORKSHEE... Solve the problems given below: 1. (a) Write a general matrix with dimensions 2 x 3. (b) Write a general diagonal matrix. (c) Write an identity matrix. 2. Find the following elements from 0 -1 4 3 (a) (b) (c) 31 [2 1 3. If A = -1 B = 4 1 find: - 2 (а) (b) A +B 28-С (c) (d) AC CA (e) Show that A(B + C) = AB + AC Г2 1 4 4. If A =3 0 B = 2 - 2 4 - 2 a d find C = be if A +B+C = 0. |e f -4 If A = 3 and B 3 -2 5. (a) find AB. What does this mean? (b) Confirm the answer to (a) by finding A using the formula A= B Find x if (3 21- = [0). MATHY Maihemtical Mathods in Physia [2 -1 If A= 3 0 1 -1 find 7. B= (а) A' (b) (c) B' (AB) B'A (d) (e) AO B Find the inverse of the following. 8. [2 17 (a) A = 3 2 [o -1 B (b) 3 0 (c) C= - 1 3 ...
Lab 4: Vectors nitude of 8.4 km and points 2. Components of vectors. The vector in this problem is a velocity vector which starts at the origin, has a magnitude of 11 m/s and has a direction of 135 degrees (measured counter clockwise from the +x axis). a. Using the gridlines below (0.5 cm spacing), draw the vector. This time, choose your own scale factor. Record your scale factor below. Make sure your scale factor is large enough so that your vector takes up most of the space in the diagram. Use a protractor and ruler to make sure your vector has the correct magnitude and direction. b. Draw a dotted line from the tip of the vector to the x axis. Using a ruler, measure the the x component in cm, and use the scale factor to convert to m/s. boltol c. Draw a dotted line from the tip of the vector to the y axis. Using a ruler, measure the the y component, and use the scale factor to convert to m/s. 5
Needs Complete solution with 100 % accuracy. Otherwise skip if you can't give complete solution for both of them.