1. Given a Parallel Resistive - Inductive circuit as shown, determine the: 240 V 60 Hz R 152 = = AL___° 1. Inductance of the Inductor, L = 2. Current flow through the resistor, IR 3. Current flow through the inductor, IL 4. The total line current, I, = 5. Circuit Impedance, Z 6. Circuit Conductance, G = 7. Inductive Susceptance, B₁ 8. Circuit Admittance, Y 0 = mS L_° = 9. Phase angle between the V and 10. Phase relationship of V and I, : ell QL_° mS L mS L___° I₁,0 XL 2002 H = _AL_° AL_ O

1. Given a Parallel Resistive - Inductive circuit as shown, determine the: 240 V 60 Hz R 152 = = AL___° 1. Inductance of the Inductor, L = 2. Current flow through the resistor, IR 3. Current flow through the inductor, IL 4. The total line current, I, = 5. Circuit Impedance, Z 6. Circuit Conductance, G = 7. Inductive Susceptance, B₁ 8. Circuit Admittance, Y 0 = mS L_° = 9. Phase angle between the V and 10. Phase relationship of V and I, : ell QL_° mS L mS L___° I₁,0 XL 2002 H = _AL_° AL_ O

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

V1 ZT Z2 V2 V3 Z5 Z3 Z4 Figure 18.4 See Figure 18.4. In a general bridge circuit such as this, what condition will result in a balanced bridge? Z1Z4 = Z2Z3 Z3 = Z4 O ZĄZ3 = Z2Z4 O Z1Z2 = Z3Z4
Answer/solve the following problems. 1. Convert the following currents to polar form : a) 6 – i 8, b) – 6 + ¡8 , c) – ¡5.
Consider the following circuit used to provide power for an induative RL load. The input voltage is V-100V and the load has a 50 impedance value. The thyristor is working at a frequency fs = 2 kHz. The discharge current is to be limited to 40A and the required dv/dt is 40V/us. If the value of Ce is equal to 0.14uF, then the snubber losses are equal to: R. V. Select one: O a 5.4W O b. 7.4W 1.4W Od. 3.4W
I dont understand phase shift and lags?
A sinusoidal current of 5 Arms is flowing through a series combination of a resistor and Inductor. The value of R is 45 ohms and that of the inductance is 15 mH and a frequency of 60 Hz. Find the magnitude and the phase angle of the voltage across the combination. (Hint: you can use phasor diagram). Select one: a. [V]=28.89, angle=9.39 b. IV]=25.60, angle367.00 c. [V]=128.01, angle3D10.18 d. IVl=226.77, angle=D7.16
3. An inductor having a 50 ohms resistance and 100 ohm inductive reactance is connected to a 100 volts, 60 hz a-c source. Draw the phasor diagram and waveform diagram of the current and voltage of the circuit showing their phase an
For the ac network of Figure Q5, calculate the following; i. The total impedance; ii. The inductance and capacitance values; ii. The total current drawn from the source: iv. Voltage VL and Vc. Xc 120 %3D R =90 X = 62 %3D ll + VL + VR VC E=30L-60° Frequency=50HZ ZT Figure Q5
detalls by Q-2: Explain the phase difference between voltage and current for a sinusoidal source voltage V(t)= Vo sin(wt) when it is applied in a circuit to a) On a resistor, b) on a solenoid, c) on a capacitor. Draw a separate figure for each case for voltage and current.
Three identical Y-connected loads, each having a resistance of 20 22 in parallel with an inductor, are connected to a three phase supply of 400 V and 50 Hz frequency. The power absorb by the load is 8 kW and power factor at the load is 0.9919. (i) Determine the current that flows through the inductor. Please state the assumptions used to solve the question. Calculate load inductance in Henry (H).
b) A circuit consists of an inductive coil (L 0.1 H, R 102) in series with a variable resistor (0 210 2). Draw to scale the locus of the current vector when the circuit is connected to 230-V, 50-Hz supply mains and the resistor is varied between 0 and 100 2.
Clear and correct or dislike
Need asap