1. For the circuit of Figure 1, a load having an impedance of 28+j162 is fed from a voltage source through a line having an impedance of 2+J4Q. The effective or rms value of the source voltage is 220V. (a) Calculate the load current IL and voltage VL. (b) Calculate the average and reactive power delivered to the load. (c) Calculate the average and reactive power delivered to the line. (d) Calculate the average and reactive power supplied by the source. 20 j42 280 220/0 V (rms) j16n Source- -Line- - Load Figure 1

1. For the circuit of Figure 1, a load having an impedance of 28+j162 is fed from a voltage source through a line having an impedance of 2+J4Q. The effective or rms value of the source voltage is 220V. (a) Calculate the load current IL and voltage VL. (b) Calculate the average and reactive power delivered to the load. (c) Calculate the average and reactive power delivered to the line. (d) Calculate the average and reactive power supplied by the source. 20 j42 280 220/0 V (rms) j16n Source- -Line- - Load Figure 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If the line-to-line primary voltage and line current is 1.0 at 0 degrees, what is the secondary line- to-line voltage for the following three-phase transformers? Assume a turns ratio of N = 10. Express answer in polar form. a. Delta-to-Delta: b. Delta-to-Wye: c. Wye-to-Delta: d. Wye-to-Wye:
Electrical load that draws current whose impedance varies throughout the cycle of the input ac voltage waveform is known as nonlinear load. True False
Find the voltage average and the voltage waveform for the output of the circuit shown below.
Please explain in detail. A. In a series circuit, if the AC voltage is measured across the AC voltage source, will there be any variations in the phase of the AC voltage across each resistor from the measured AC voltage across the source? B. In an AC voltage source, why does voltage vary with time? Please explain in detail. C. In a series circuit, are the frequencies of the AC voltages across each resistor the same? Why is this so? ...
Under short circuit, the reactance’s of the synchronous generator during the steady state condition are following, Leakage reactance(Xl)= 0.11 ohm and Armature reactance (Xad)= 0.7 ohm The direct axis synchronous (steady state) reactance (Xd) is
How about the average power on each elements? And is it absorbing or delivering power too?
Consider the circuit shown in Figure 1. V1 is a 7.2 kHz sine wave with an amplitude of 4 V.Figure 1: RC Circuit Schematic1. Determine the total impedance (Z) of the circuit.2. Using V1 as a zero-phase reference, calculate the values of the following:a) Amplitude and phase of current (I)b) Amplitude and phase of voltage across R1 (VR1)c) Amplitude and phase of voltage across C1 (VC1
The output of a station with two alternators in parallel is 40MW at 0.75 power factor lagging. One machines is loaded to 20,000KW at 0.8 power factor lagging. Determine the: a. KVA rating and power factor of the load b. KVA rating and power factor of the other alternator
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
A 60 Hz sinusoidal voltage v = 141sinwt is applied to a series RL circuit. The values of the resistance and the inductance are 3 ohms and 0.016 henry respectively. a) Compute the rms value of the current and its phase angle with respect to the voltage. b) write the expression of the instantaneous current.
From the figure, a Obtain the transfer function Eo(s)/Ei(s). b Sketch the response of eo(t) due to a step change in ei(t) of 2 V. Hint: arbitrarily pick values for L, C, R1, R2