1. For our permanent magnet motor, using Ko = 0.06 N-m/A or 0.06 V-s, a. Calculate the no-load speed for a supply voltage of 18 V. b. If the starting (zero speed) developed torque is 1.8 N-m when 24 V is supplied, determine the torque and current draw at the design operating speed of 3000 rpm.

Q: What is the main difference between a BJT and a FET? a. both are three pin device b. BJT is a…

A: Different loads require different specifications to work. Analog devices are used for delivering…

Q: Give the verilog code to detect pattern 10110.

A: Verilog is Hardware Description language . The state diagram is visual representation of the…

Q: Design a synchronous counter using JK flip-flops to produce the following sequences. 3 5 1

A: According to the question, we need to design a synchronous counter, which follows the following…

Q: O Given, the hexadecimal number is E816, convert it to the octal number and display the octal number…

A: In this question,  We need to convert the hexadecimal to the octal number.  E8H  ---> (?)8

Q: Consider a 8-bit ADC and full scale voltage measurement range of (-29 to 29).The Resolution  will be…

A:

Q: In N-channel JFET the Id is controlled by_______. a.Idss b.Vgs c.Vds d.Ig

A:

Q: c) Given the changed lines of code below, answer the following questions. ANALOG_COMPARE_SETUP: LDI…

A: The given code is shown below.ANALOG_COMPARE _SETUP:LDI R16,0STS ADCSRA, R16LDI R 16, 0b00000000STS…

Q: In HDB3, If the number of non-zero pulses is even, the format used is a. V000 b. B00V c. V00B d.…

A: The HDR-3 is HIgh Density Bipolar 3 Zero Coding.It is more conservative than other coding methods

Q: 7) The following readings are obtained in the measurement of an inductor: 1.003,0.998, 1.001, 0.991,…

A:

Q: Jump to level 1 a b C 1 0 0 10 10 0 N Z=c+a Delete selected item(s) Undo Click to add DAK

A:

Q: How must the uno be configured to create a traffic light? A. Pins can be configured any way B. 1 pin…

A: Arduino Uno :  The Arduino Uno is a microcontroller board based on ATmega32u4.

Q: Refer to the National Electrical Code or the working drawings when necessary. Where applicable,…

A: We are authorized to answer one question at a time, since you have not mentioned question you are…

Q: +V1ev1- L3 13/23 R2 v5 es V4 e4 |12/02 Figure 2060

A:

Q: a) Plot both the engineering stress versus engineering strain and true stress versus true strain…

A: Note: As per Bartleby guidelines, I have provided solution of first three questions a, b and c. You…

Q: is the simplest way of producing a source of lower EMF from a source of higher EMF.

A:

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: In N-channel JFET the Id is controlled by___ a. Vds O b. lg O c. Idss O d. Vgs

A: JFET is controlled by the Gate voltage and current equation in saturation region is given by , ID =…

Q: Assume that carry flag is 1 at the beginning, and execute the following code: mov al, OE8H rcl al, 1…

A:

Q: 32K×4 A14 En • CS

A:

Q: represents a circuit breaker with thermal overload protection? A. C B. D C. A D. B

A:

Q: Need solution within 15 mins. Give 5 stars for correct solution

A: The solution is provided in the following section:

Q: Propagation delay is usually measured in O a. milli-volts O b. nano-seconds O c. nano-Watts O d.…

A: We need to tell about unit of propagation delay

Q: Where does 23/332 for N1/N2 come

A:

Q: Q-1) هد Please write the magnetic circuit And explain the steps.

A: Given figure:Asked to explain the ircuit and write magnetic circuit?

Q: Microsoft Whiteboard Request control DC Pi log Po PI Gdev = I0 log 20 48M 2/24/2001 ansino O Type…

A: This is simply conversion of linear scale to dB scale  Since gain = (output power)/(input power)

Q: Eg k.1/ Prove that: ni = NcNy e KT? %3D Using Eg = Ec- Ev

A:

Q: 110 About indistrial piping WHY IS THE ASME 31.3 ALLOWABLE VOLTAGE A COMBINED VOLTAGE?

A: According to the question, WHY IS THE ASME 31.3 ALLOWABLE VOLTAGE A COMBINED VOLTAGE?

Q: Horizontal Controls Autoset tical Controls Trigger Controls

A:

Q: deterptiar the alue to a clese leep Coantael Date. tn a cteed teep Contrel system $s Hal, yte due to…

A:

Q: Solve for ID in IMG 18 V 2kQ 1100 mA. round off your answer with 1 decimal value V-1.7 V 0.51 k

A: FET are voltage controlled device. BJT is current controlled device JFET is stand for Junction field…

Q: HW14/ H.W: control the intensity of the LED by serial.

A: We required the following elements for the following to control the LED Arduino Board Led Arduino…

Q: Display all the numbers from 20 to 1 using while loop.

A:

Q: Define and differentiate HPLC and Reverse Phase LC

A: Brief description : In the above given question they want to have a definition and difference…