Problem 1: For each of the plane stress states listed below, draw a Mohr's circle diagram properly labeled, find the principal normal and shear stresses, and determine the angle from the x axis to ol. Draw stress elements as in Fig. 3-11c and d and label all details. (a) as = 20 kpsi, ay--10 kpsi, tay 8 kpsi (cw) (b) a = 16 kpsi, oy 9 kpsi, Tay 5 kpsi (ccw)

Problem 1: For each of the plane stress states listed below, draw a Mohr's circle diagram properly labeled, find the principal normal and shear stresses, and determine the angle from the x axis to ol. Draw stress elements as in Fig. 3-11c and d and label all details. (a) as = 20 kpsi, ay--10 kpsi, tay 8 kpsi (cw) (b) a = 16 kpsi, oy 9 kpsi, Tay 5 kpsi (ccw)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

:Construct a Mohr circle using below information and label it appropriately. Using Mohr circle, find out maximum and minimum principal stresses and their orientation. Show them in a differential volume of element. 100 MPa 75 MPa 150 MPa
Question: Find schematically the normal and shear stresses in the plane when the element in the plane stress state is rotated 30 degrees counterclockwise with the Mohr circle.
Determine the state of stress acting at point D. Take P₁ = 120 kN and P₂ = 45 kN. (Figure 1) Figure L -1.5m- +1.5m-1.5 m- 0.5 m 40 mm 100 mm 60 mm 80 mm 1 of 1 > Find op- Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. od= - 154.88 Submit Part B Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining MPa Find TD- Express your answer to three significant figures and include the appropriate units. JA TD= Value Units ?
4-16 Consider the stress state of Problem 4-13. Redo the problem for shear stresses of 0, 0.2, and 0.3 MPa. What effect do you observe on (a) the magnitude and (b) the direction of the principal stresses as the applied shear stresses increase? 0.1 MPa 0.1 MPa 1 MPa 60° 1 MPa 0.1 MPa 0.1 MPa Figure 4-45 State of stress at a point for Problem 4-13.
A state of plane stress is illustrated in the stress element in Figure 3. (a) (b) 30 MPa Figure 3. 40 MPa 60 MPa y X Find the center, X and Y of the Mohr circle. Plot the Mohr circle using these points. From the Mohr circle, find the principal stress and the maximum shear stress. Indicate on the Mohr circle where these values are found.
Using Mohr's Circle, solve Review problem R9-5 in the 10th Ed. of the text. Plot your solution along with notation of the axes and all the values below on graph paper. Show your calculation for the values below. 1. Find the Principal Stresses, and the orientation of the element at the those stresses 2. Find the maximum in plane shear stress, and the orientation of the element at that stress 3. Find the absolute maximum in plane shear stress 4. Find the normal stresses and shear stress when the element is rotated 30 degrees counterclockwise 30 ksi 10 ksi R9-5
Fill in the blanks. Draw and label the Mohr’s circle. For sigma-yp = 30 kSf. does this fail? Find the stresses on the plane shown. Find the plane on which sigma-1 acts relative to the horizontal. Draw them on the figure. Draw the Tresca plot.
For the flat stress state shown in the figure. Use Mohr's circle to determine (show the procedure only with the use of geometry): a. Draw Mohr's circle indicating coordinates of the points that represent the given stress state, center, radius, coordinates of the points that represent the state the maximum and minimum normal stresses, coordinates of the maximum shear and angle of rotation from the stress given to the plane principal. b. Use the results of literal a to draw the element subjected to main forces and the element subjected to maximum shear. 12 MPa 19 MPа y 19 MPа 46 MPа 46 MPа 19 MPа 19 MPа 12 MPa
PROBLEM 3. The stress condition at one point in the tail region of the National Combat Aircraft is shown in the figure. (a) Calculate the principal stresses (b) Calculate the maximum in-plane shear stress and the average normal stress by analytical method and plotting the Mohr's circle. For each case, determine the element orientation and plot the stress state. (c) Calculate the maximum absolute shear stress at the same point. 40 MPa TAI 200 MPa 80 MPa
Q-1 Figure Q-1, below, shows Mohr’s circle for a point in a physical object that is subjected to plane stress. Determine the stresses σx, σy, and τxy, and show them on a stress element, properly oriented with reference to x-y axes. Determine the principal stresses σ1, σ2, and τmax and show them on a stress element properly rotated with respect to the x–y element Determine the stresses σn, σt, and τnt, and show them on a stress element that is properly rotated with respect to the x–y The sketches must include the magnitude of the angles w.r.t. positive x-axis as well as the angle between the x and n axes, and an indication of the direction of rotations (i.e., either clockwise (c.w.) or counterclockwise (c.c.w.)).
Consider the following plane stress state: Ox=30 MPa, y= -60 MPa, Txy= 30 MPa cw Calculate the following: 1. The coordinates of the center of the Mohr's circle C The location of the center of the Mohr's circle Cis ( 2. Principal normal stresses (01, 02) The principal normal stresses are σ₁ = 39.08 3. Maximum shear stress (7) The maximum shear stress is 54.08 MPa. 4. The angle from the x axis to 0₁ (p) The angle from the x axis to 0₁ (p) is -16.85 5. The angle from the x axis to 7 (s) The angle from the x axis to T (s) is 28.15 6. The radius of the Mohr's circle The radius of the Mohr's circle is 54.08. ✰ MPa. MPa and 02 = -69.08 MPa. O -15 MPa, CW CCW O MPa).
At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane stress condition determine: -all 3 principle stresses, the max in plane stress, average noemal stress and the absolut max shear stress. - Show the principle stress, the max inplane shear stress and the average normal stress on an appropriate schematic