Q1: Choose the correct answer from the following:1. For an open circuit (OC) load, the value of the reflection coefficient equal to(a) 1(b)-1(c) infinity(d) 02. If the voltage of the carrier(Voc) is greater than from the Voltage message (Vm).Therefore the value of the modulation index (m) would be,(a) greater than 1 (b) less than 1 (c) equal to 1 (d) infinty3. For ZR #Z0, the total reflection is occurred when the load is short circuit. the value ofthe voltage and the current Exets Ixsts(a) Ext=max, Ixt = 0(b) Exal = 0, Ixal = max(c) Exet = max, 1x==max(d) Ext=0, 1x1 = 04. The electrical distance (as a function of the wavelength) between two successive minimumvoltages in the standing wave pattern of a TL is equal to(a) 0.2(b) 0.25(c) 0.5(d) 0.755. The highest power efficiency can be achieved in the conventional DSB-AM modulation(b) 33%is:(a) 23%(c) 53%(d) 73%

Dear student, Since you have posted multiple questions, we will provide the solution only to the…

Answered: 1. For an open circuit (OC) load, the…

Engineering

Electrical Engineering

1. For an open circuit (OC) load, the value of the reflection coefficient equal to (a) 1 (b)-1 (c) infinity (d) 0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Phase shift due to finite length of circuit conductors. On a particular type of circuit board, assume a signal travels at 2/3 of the speed of light. Suppose a high-speed system using this type of board can tolerate a phase shift in a sine-wave signal due to propagation delay of only 15° before failing to work. Calculate the maximum length /MAX (in m, or a suitable subdivision such as cm or mm) that a circuit-board trace carrying this signal can have at each of the following frequencies without encountering excessive phase shift due to the propagation delay along the trace: (a) f=10MHz, (b) f=30MHz, (c) f=500 MHz, and (d) f=2.5 GHz.
The power of operating frequency in AM station is 145 W, and there is 89% modulation depth. (assuming single side band suppressed carrier). What is the power of the side bands?
Please help me answer number 4. Please show a CLEAR and READABLE solution/s. Thanks!!! The course subject is Fundamentals of Electronic Communications.
Figure 1 shows the AM waveform envelope generated with a carrier frequency of 20 kHz and a modulating frequency of 1 kHz. 0.5 -0.5 -1.5 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 Time, seconds x 10 Figure 1: Plot of AM Waveform. Determine: i) Modulation index. ii) Carrier signal equation. iii) Information signal equation. iv) Sketch the frequency spectrum of the AM signal. v) Bandwidth of the signal. vi) Total power of the signal, given the resistance is 50 2. AM Signal, V
answer b
Problem 5. A carrier wave of frequency 20 MHz is frequency-modulated by a sine-wave of amplitude 2 volts and frequency 4 kHz. The frequency sensitivity of the modulator is 10 kHz per volt. a) Determine the approximate bandwidth of the FM wave using Carson's rule. b) Repeat part (a) assuming that the amplitude of the modulating wave is doubled. c) Repeat part (a) assuming that the modulation frequency is doubled.
The energy per bit to noise ratio for the following parameters is______________. C=1nW, N=1pW, fb=56kbps, B=200kHz
Subject:communication. Need solution
Problem 4 to separate ITU channel 59 using a fiber Bragg grating (FBG) and an optical circulator. The FBG is made from a fiber with an effective index of refraction of the core of 1.48 at You are to implement a simple one-channel demultiplexer ITU channel 59. a.) Draw a diagram of the demultiplexer b.) Calculate the periodicity of the index of refraction modulation in the core of the FBG fiber
For an AM envelope with a maximum peak voltage of 52 V and a minimum peak to peak voltage of 24 V, determine the ff. a. Percent modulation = ________? b. Peak voltages of the carrier and side frequencies = ________? c. Maximum positive to negative envelope voltage = ________?
None
Q6. Figure Q6 shows the line spectrum of a modulated signal (all components are positive and real). 3 1 232 234 236 238 frequency/kHz Figure Q6: Line spectrum of a modulated signal (a) Describe the modulation scheme. (b) What are the values of the carrier frequency, modulation frequency and the modulation index? (c) What is the transmission efficiency (ratio of modulated to total power) in this example? (d) The reception of this signal is undertaken with a superheterodyne detector using an intermediate frequency of 110 kHz. What is the appropriate local oscillator frequency? (e) Demodulation of this type of signal is usually accomplished using an envelope detector. Describe the principles of operation of an envelope detector and sketch an example circuit. (f) What considerations should be made about the component values in the design of an envelope detector in order to demodulate the signal after shifting to the intermediate frequency? Relative unitsS