1. Find the power input required by the pump if pump efficiency is75%.Pa60°FPgsPgaZa- 50' (15.24 m)Zga = Zg.Ze- 6 (152.4 mm)Z, - 5' (1.524 m)ho - 25' (7.62 m)h3' (0.9144 m)60°FH20

Answered: Image /qna-images/answer/7332090f-7236-40db-a18d-1e65dc8f7455.jpg

Answered: 1. Find the power input required by the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is Total Head of submersible pump has Q=287 l/sec D=0.8 m Lenght of pipe=12000 m Fluid=water Fittings=6 elbows 45 degree Material=GRP Depth of well=9 meter Please take your time
For a 6.25-inch Model 4075 pump operated at 1160 rpm, if 450 GPM of water is to be delivered, what will be the estimated pump head in ft? HEAD IN FEET 30 25 0 0 0 10 O 6 ft 7.25" (184mm) 20 7.00" (178mm). 6.75" (171mm). 6.50" (165mm)] 15 6.25" (159mm). 5 O 16 ft O 20 ft O 12 ft aco® L/SEC 5 OT 10 Model 4075 FI & CI Series 15 -6-6 ⁰ dº 20 ANA 888 778 25 REQUIRED NPSH do 1160 RPM November 1, 2010 K ・dº- [M 90 do 30 8800 81 1HP(.75KW) DeJ kin do 60% 35 do 50 Curve no. 2175 Min. Imp. Dia. 6.25" Size 5 x 4 x 7.0 40 45 3HP(2.2KW), 2HP(1 5KW) 5HP(1 1KW)> CURVES BASED ON CLEAR WATER WITH SPECIFIC GRAVITY OF 1.0 L 75 150 225 300 375 450 525 600 675 FLOW IN GALLONS PER MINUTE NOWONG FEET 15 12 7 6 2 1 NPSH 758 50 5 HEAD IN METERS 45 586888 KPO 60 40 20 10 LO HEAD IN KILOPASCALS
4. A pump is tested in the laboratory and the following data were obtained. Torque = T= 6.78 Nm Rotational speed = w = 20 Hz Inlet pressure = P1 = 68.95 kPa Outlet pressure = p2 = 193 kPa Velocity in the inlet line = V= 2.44 m/s Height to inlet gauge = z1 = 0.61 m Height to outlet gauge = 22 = 1.52 m Inlet flow line = 2- nominal schedule 40 Outlet flow line = 2- nominal schedule 40 Fluid = Water a) Determine the pump efficiency. b) Consult an actual pump catalog and select a pump for these conditions.
Q4/A- The mass of the filter is 25.3046 gm. after 20 min the filter mass will be 25.4112 gm. with volumetric flow is 5.2 m 3/hr. What is the concentration of pollutant after one day
The general energy equation is . For the picture blow, select the simplified the form of the general equation for point 1 and 4____________
a) Develop an equation for the head (in ft) developed by the pump described by the chartas a function of flow rate (in gpm) when the pump uses a 9 ¾” impeller. b) Develop an equation for the pump efficiency as a function of flow rate (gpm) when the pump uses a 9 ¾” impeller.
A model of a hydraulic turbine is tested at a head of 1/4th of that under which the full scale turbine works. The diameter of the model is half of that of the full scale turbine, if Nis the RPM of the full scale turbine, then RPM of the model will be
Please solve question hand written
### Develop a conclusion of a piping design report for the choice of a pump, based on the calculated parameters of flow Q = 10 l/s, power of 10kw taking into account that the head of 60 mca adopted was higher than that calculated for safety, and that the pump was chosen through the WebCAPS catalogue of the company GRUNDFOS. The pump chosen was the GRUNDFOS CR 32-3 A-F-A-E-HQQE
Determine the % increase in Flowrate, Net pumping head and Pump power based on the following conditions below: a) Increasing the impeller speed by 30% b) Increasing the impeller diameter by 20% c) Compute the same if the two conditions above will prevail in one condition Please show complete solution.
Pls to step by step

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

1. Find the power input required by the pump if pump efficiency is 75%. P 2 60°F Za - 50' (15.24 m) Pgs Pga Zga- 6" (152.4 mm) Zga = Zgs %3D Z- 5' (1.524 m) ho 25 (7.62 m) he 3' (0.9144 m)