1. Each of the two sides of a hand-operated toaster can be operated independently of the other. A spring holds each side of the toaster shut, and each side must be held open in order to insert bread. Assume that the toaster is hot and ready to toast bread. The following are the elemental times necessary to perform the operations. Assume also that both hands can perform their tasks with the same degree of efficiency. Side Place slice of bread in either side of toaster: 4 seconds. Toast either side of bread: 30 seconds. Side B Turn slice of bread on either side of toaster: 2 seconds. Remove toast from either side of toaster: 4 seconds. By using a man machine chart for toasting 3 slices of bread, what method would you recommend to obtain the best equipment utilization that is, the very shortest overall time?

Q: answer is 900.8 please resolve

A: Given Data

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: solve and show every step with right answer

A: Data given - Rectangular cross section 225×75 mm2 Torsional moment = 20kN Axial Compressive force =…

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP FRP L FRP PRP L

A: The isometric view is given in the above figure.We have to find out multiview of the given isometric…

Q: The velocity of the piston is 52.9901 3 ft/s.

A: use sine rule

Q: Draw the orthographic views of the following isometric figure.

A:

Q: 20 30 R15 5-Ø10 R10 Ø40 10 40 40 Figure 1

A:

Q: The total positional tolerance equals the sum of the tolerance. O bonus and plus/minus O limit and…

A: According to the given data, we need to fill in the blank part.

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: A drilling machine is to have 8 speeds ranging from 100 rev/min to 1000 rev/min. if the speeds from…

A: The total number of terms for this AP is: n=8 The first number is: a=100 rev/min The last number is:…

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: Round off the numbers in the following problems to three significant figures. Find the percent…

A: Given Data: The given number is N = 826.48 The number should have three significant figures, hence…

Q: 200 m The spool has a mass of 40 kg and a radius of gyration of k-0.65 m. If the 20 kg weight is…

A:

Q: For the given isometric drawing, draw the corresponding top, front, and right side view. L HRP FRP L…

A: For the given isometric drawing, draw the corresponding top, front, and right side view.

Q: What is Line J? ARROWHEAD .35mm A 7.0 В

A: Solution:

Q: both answers are wrong :(

A: Given DataT1=310KP1=320kPaM1=0.3 To findV2=?P2=?

Q: The number of teeth on a gear is 27 and the outside diameter is measured as 10 mm. The module of the…

A: Given Data No. of teeth is 27 Outside diamtere is 10mm

Q: An 4 cylinder engine has a crankshaft sp of 3,500 rpm, a bore of 3.8 inches, a str of 3.8 inches,…

A: Givenk=4N=3500 rpmd=3.8in =3.8×0.0254=0.09652mL=3.8in=3.8×0.0254=0.09652mP=210…

Q: G R.75 00.63 THRU 01.123 F0.250 1.00 chamfer with distance 0.25 mm fillet with radius 0.25 mm fillet…

A: Select the correct statement about the notation circled in green and marked as letter F. Assume all…

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.