1.Draw the reactance diagram for the power system shown below.1Line 1220kV66.5MVAT2T1Motor10.45kVGenXp.u.=0.1855Line 290 MVA3ph Load 10.45kV110kV22kVAbsorbs 57MVAXp.u.=0.18T3T4@ 0.6pf (lag)22/220kV Xp.u.= 0.10220/11kV Xp.u.= 0.0622/110kV Xp.u.= 0.064110/11kVT1:50MVAT2:40MVAT3:40MVAT4:40MVAXp.u.=0.08Line 1: 48.40hms (total)Line 2: 65.430hms (total)

Power System : The power system is a network that includes the generation, distribution, and…

Answered: 1. Draw the reactance diagram for the…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
60. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the real power. a. 65.3899 b. 392.4372 c. 397.848 d. 588.6559
3- Please I want answer of this Electrical Principles question. Thanks
Q4. The source current in the circuit shown is in Figure 3a) What impedance should be connected across terminals a,b for maximum average powertransfer?b) What is the average power transferred to the impedance in (a)?c) Assume that the load is restricted to pure resistance. What size resistor connected across a,bwill result in the maximum average power transferred?d) What is the average power transferred to the resistor in (c)?v
Determine the effective resistance R of the network exhibited in the figure. Each Ris 2.2 2A sinusoidal alternating voltage has an rm.s, value of 200 V and a froquon
AC xuf lac V ac 21. The simple AC powered circuit above is being measured for AC current and voltage across a 1uF capacitor. The measured current is 200mA and the measured voltage is 40V. (note: 2 separate questions follow) a. Calculate the capacitive reactance, Xc. b. Calculate the voltage frequency.
Three generators are rated as follows: G1: 100MVA, 33kV, xg1 = 0.1pu G2: 150MVA, 32kV, xg2 = 0.08pu G3: 110MVA, 30kV, xg3 = 0.12pu. Determine the reactance of the generator corresponding to base values of 200MVA and 35kV
A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 p.u. Where as before the fault, this power was 2.5 p.u. and after the clearance of the fault, it is 2 p.u. The value of 8 is max
I need the answer at 20 minute
step down chopper has Vs = 230 V and R = 10 0. For a duty cycle of 0.4, the power taken by the chopper is 2097 Watts. Find the chopper efficiency. Take the voltage drop across the chopper switch as 2 V. a) 98 % b) 89.96 % c) 99.14 % d) 96.54 %
12th sum Please solve me
Where did it come from?

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning