1. Draw the N.L characteristics and external characteristics Of series generator, draw the different external characteristics. For two types of compound generator on one sheet. 2. Does the external characteristics of series generator represent its load characteristics? Why? 3. What is the difference between cumulative and differential compound generator?

1. Draw the N.L characteristics and external characteristics Of series generator, draw the different external characteristics. For two types of compound generator on one sheet. 2. Does the external characteristics of series generator represent its load characteristics? Why? 3. What is the difference between cumulative and differential compound generator?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Similar questions

T-a. The direction of rotation of a single-phase split-phase motor can be change by........ a) reversing the connection of the start winding b) reversing the connection of the run winding c) reversing the connection of the start and run winding at the same time d) "a" or "b", not "c" T-b. Single-phase split-phase motors using an electrolytic capacitor in the start winding circuit should not be cycled more than about__________ time per hour. a) 8 b) 12 c) 24 d) none of the above T-c. When replacing the capacitor in a capacitor-start induction-run motor, one must be sure to replace the bad capacitor with__________ . a) a smaller one b) one of the same size c) a larger one d) none of the above
Can you please answer Problem 49 to 51.
A short shunt compound generator delivers 150A at a terminal voltage is 230V. The shunt field current is 2.5A. The resistances of the armature, series field and diverter are 0.032-ohm, 0.015 ohm and 0.03 ohm, respectively. Calculate the electrical efficiency of the generator at this load.
D2. When a generator's full-load output voltage is the same as its no-load output voltage it is said to be a) under-compounded b) flat-compounded c) over-compounded d) none of the above D3. The output of an overcompounded DC generator can be lowered by use of a a) rheostat connected in series with the series field b) rheostat connected in parallel with the series field c) rheostat connected in parallel with the shunt field d) none of the above D4. When might it be desirable to use an overcompounded generator? a) never b) always c) to compensate for line loss d) when you need a higher no-load voltage than your full-load voltage
(Ipp. I., D. O.) 12. Calculate the number of series turns per pole required on a compound generator to enable it to maintain the voltage constant at 460 V be- tween no load and full load of 100 kW. Without any series winding, it is found that the shunt current has to be 2 A on no load and 2-65 A on full load to maintain the voltage constant at 460 V. Number of turns per pole on the shunt winding = 2000 If the series coils were wound with 8 turns per pole and had a total resistance of 0-01 2, what value of diverter resistance would be re- quired to give level compounding?
Plz answer all parts
. When a self-excited compound DC generator supplies load, the terminal voltage is not the same as the generated emE Why? a) voltage drop across the armature resistance will reduce the voltage available at the load terminals b) where there is a series field, voltage drop across the series field resistance will reduce the voltage available at the load terminals c) both "a" and "b" d) neither "a" nor "b"
Please solve this problem step by step and illustrate your answer properly. Write your answer in a piece of paper please. Box the final answer.
For DC shunt generator, external characteristics is the relationship between Answer:
A 6 pole wave wound d.c. shunt generator has 500 conductors. A generator delivers 50 kW of power at 250 voltage at full load. The resistance of the field circuit is 125 2. Actual brush shift is 10°. Then find the demagnetizing and cross magnetizing ampere turns per pole and how many additional turns must be wound on each pole to eliminate the demagnetizing effect.
The power factor of an alternator depends on on Load а. b. Speed of rotor Core losses C. d. Armature losses
A d.c.series generator has armature resistance of 0.5Q and series field resistance of 0.032.It drives a load of 50 A.If it has 6 turns/coil and total 540 coils on the armature and is driven at 1500 r.p.m.,calculate the terminal voltage at the load.Assume 4 poles, lap type winding, flux per pole as 2 mWb and total brush drop as 2 V.