1. Draw a free body diagram for the block on the ramp that is attached to the string. There is no friction between the block and the ramp. The angle of the ramp is 35 degrees with respect to the horizontal, and the angle of the string is 45 degrees with respect to the horizontal. The block is at rest, and it has a mass of 10 kg. The acceleration due to gravity for this experiment is 9.8 m/s?. 450 35° 2. Decompose all of the forces into x and y forces 3. Sum the x forces and set them equal to what they should be set equal to. Sum the y forces and set THEM equal to what they should be set equal to.

1. Draw a free body diagram for the block on the ramp that is attached to the string. There is no friction between the block and the ramp. The angle of the ramp is 35 degrees with respect to the horizontal, and the angle of the string is 45 degrees with respect to the horizontal. The block is at rest, and it has a mass of 10 kg. The acceleration due to gravity for this experiment is 9.8 m/s?. 450 35° 2. Decompose all of the forces into x and y forces 3. Sum the x forces and set them equal to what they should be set equal to. Sum the y forces and set THEM equal to what they should be set equal to.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The free body diagram below shows the forces acting on the bob when it spins at a rate such that it…

A: GivenFS=string force Fe=Elastic force W=weight of the bob

Q: The pressure drop across a length of pipe with flowing air is measured with an inclined tube…

Q: 21° W A 190 kN horizontal force Pis applied to a 220 kN box resting on an 21° incline. The line of…

Q: .A cart is being pulled by a motor. The cart has a mass of m = 200 kg. The motor applies a…

A: The force applied is The mass of cart is The distance of center of mass above the floor is The total…

Q: Two blocks are connected by an ideal spring on a frictionless floor as shown above. Force F is…

A: To determine the net force on block 2, it is necessary to draw the Free body Diagram.

Q: Blocks A and B weigh 30 lb and 50 Ib, respectively. В M = 0.5 20° MBA =0.6 0.6 A C D MAC = 0.4 If…

Q: Two blocks of the same mass, m, are connected by a light string and rest on the slope and in the…

A: According to the given data Both block has mass =m

Q: What normal force is exerted on the refrigerator by the floor at A? Express your answer with the…

Q: A small object of mass m is located on the surface of the disk with radius R if the magnitude of the…

A: We will answer the first question since the exact one was not specified. Please resubmit the…

Q: J The mass of A is 30 kg and the mass of B is 5 kg. The coefficient of kinetic friction between A…

Q: The horizontal position of the 50olb block (B) is adjusted by the 7° wedge (A) under the action of…

A: Friction force is defined as the resistance force offered by the surface of contact, and normal…

Q: 6. A car weighing 5000-kg is on a banked curve as shown. The coefficient of friction between the…

A: Given: The car weight, M = 5000 kg The coefficient of friction, f = 0.5 The path radius, r = 200 m…

Q: Question 2 Consider the two blocks shown above, connected together by a massless rope around a…

Q: Two blocks are being pushed along an incline. Block A weighs 7.00 kg and block B weighs 14.00 kg.…

Q: 2. A 250-lb block Is initially at rest on a flat surface that is inclined at 30°. If the coefficient…

Q: For the delivery truck shown: The mass of the truck is 4000 kg. The horizontal distance from the…

Q: A 0.3-kg block is placed against a rotating hollow cylinder of inner radius = 0.7 m. The cylinder…

A: Given data: Draw the free-body diagram of the block.

Q: 3. Two masses are attached by a string. Mass M hangs freely while mass m is on an incline of 30°. M…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

Q: Part A Determine the maximum acceleration of the truck without causing the assembly to move relative…

Q: A 4.6-kg block is pushed 2.3 m up a vertical wall with constant speed by a constant force of…

Concept explainers

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.

Question

1. Draw a free body diagram for the block on the ramp that is attached to the string. There is no
friction between the block and the ramp. The angle of the ramp is 35 degrees with respect to the
horizontal, and the angle of the string is 45 degrees with respect to the horizontal. The block is at
rest, and it has a mass of 10 kg. The acceleration due to gravity for this experiment is 9.8 m/s?.
450
35°
2. Decompose all of the forces into x and y forces
3. Sum the x forces and set them equal to what they should be set equal to.
Sum the y forces and set THEM equal to what they should be set equal to.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A hand pushes horizontally with a constant force on two blocks stacked against a wall (u, between finger and block A is zero). The blocks and wall do not accelerate. The mass of block A is greater than that of block B. The coefficient of static friction between the block and wall is the same as the coefficient of static friction between the two blocks. Draw a separate free-body diagram for each block. For each force on your free-body diagrams, be sure to indicate: • the type of force (e.g., tension, weight ...), • the object on which the force is exerted, and • the object exerting the force. a. Rank the magnitudes of the vertical forces that you have shown from largest to smallest. Explain how you applied Newton's second and third laws to obtain your answer. b. Suppose the hand pushes horizontally with a constant force that is twice as large as in part a. Would the friction force exerted by the wall be greater than, less than, or equal to the friction force by the wall in part a?…
Drew is pushing a 12.0-kg box on a floor until he runs into a horizontal spring. The values of force for a few different values of horizontal position x are (x, F): (-2, 10), (-1, 10), (0, 10), (1, 15), (2, 20), (3, 25), (4, 30). a. What is the coefficient of friction? b. What is the work done by Drew's pushing force from x = 0 m to x = 7 m, where x = 0 m corresponds to the initial contact with the spring? c. What fraction of this work goes into heat?
2. Blocks A and B weighs 1800 N and 900 N respectively. Coefficient of friction undereach block is 0.20. Assuming the pulley to be weightless and frictionless.a. What is the acceleration of the system when it moves from rest?b. What is the tension in the chord?
2. The banked turns at Talladega International Super Speedway are designed so a 1760 kg race car can drive around them at 340 km/h without slowing down. The radii of the turns are 400 m. a. If the component of friction that is directed toward the center of the circle is 35,435 N, at what angle must the corners be at in order to allow this type of race? (Show an FBD) (0 = 13°) an Swes b. What is the slowest speed a car can travel and still be able to go around a corner without falling to the bottom of the track? Ignore friction and give your answer in km/h. (Show an FBD) (v = 29 m/s) mswes
Lost on this one, any help would be appreciated. Check all possible motions
Assume that there are no frictional forces between the pulleys and the strings, and the strings are mass-less. The frictional coefficient between the1 kg and 2 kg is 0.05, the frictional coefficient between the 2 kg and 5 kg is 0.1, and the frictional coefficient between the 5 kg and the table is 0.2. (a) Draw free-body diagrams for each mass? (b) Calculate the magnitudes of normal forces and frictional forces?(c) If we release 4 kg and 3 kg from rest what are the accelerations of each mass? (System has two different accelerations)(d) Calculate the tensions in each string?
Question 2 A car has a mass of 4 Mg and the center of mass at G = 400mm from the ground. The front wheels are 1.3 m and rear wheels are 0.8 m from the centre of gravity. Coefficient of kinetic friction between the wheels and the road is 0.2. Determine the acceleration if the rear driving wheels are always slipping and the front wheels are free to rotate. Neglect the mass of the wheels.
A 0.32 lbm baseball is tethered to a string and swung by a rotating vertical pole. If the string is 12 ft long and the speed of the ball is 55 mph, determine the tension in the string, the angle the string makes with the vertical and the angular speed of the pole. ANS. 0=86.6°, T = 5.4 lbf, o=6.73 rad/sec
A carnival ride has people stand inside a vertical cylinder with their backs to the wall. The cylinder starts spinning and the riders find that they are “stuck” to the wall and don’t slide down, even if the floor is removed. The ride has a radius of r. The person has a mass of m and is moving with a constant speed of v. The coefficient of static friction between the person and the wall is μs , and kinetic friction μk. The person is only touching the wall, not touching the floor. What is the magnitude of the acceleration of the person? In what direction does it point? The speed is constant. Why is the acceleration not zero? Briefly explain. No equations!
The uniform 52-kg slender bar is initially at rest on a smooth horizontal plane when the forces are applied. If P₁ = 20 N and P₂ = 86 N, they are constant and are always perpendicular to the slender bar, determine angle (in degree) when time t = 0.40 s has passed. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. 0.75 m P₁ Your Answer: Answer 1.75 m 0.5 m P₂
2) After playing a game of pinball, you decide to do some calculations on the launching mechanism. The pinball and the plunger have a mass of 0.30 kg and 0.50 kg respectively. The spring coefficient in the pinball machine is 300 N/m. The original length of the spring is 100 mm and the compressed length is 35 mm. If the coefficient of friction between the ball and the surface is 0.15, calculate the velocity of the ball right before it loses contact with the plunger (in m/s). Note that the plunger is never in contact with the ground and assume the ball slides without rolling. [Ans. to check: 1.23 m/s] HO www
Motorized moving platform is lifting a car with some acceleration. If the combined weight of the lift platform and car is 2800kg, and the motorized lift weight is 200000kg, determine the maximum acceleration of the platform before tipping occurs. Weight of the platform a=2.1m, b = 4m, c = 4.2m, d = 3m FBD of the lift: Vertical lift platform. center of gravity (car) FBD of the car: a C Too center of gravity (lift)