stresses in beams 1.Determine the maximum tensile and compressive bending stresses inthe beam shown.4 kN/m200 mm-1= 30 x 10 mmB6 mNA80 mm2.For the beam shown in the figure, find the shear stress at a point 30 mmabove the bottom of the beam at section C.50 mm|14 kN1.5 mB3 m100 mm1 = 19.3 x 10 mm- NAAD62.5 mm50 mm2 m100 mm 3.For the beam shown, calculate (a) the maximum bending stress; and (b) thebending stress at a point 0.5 in. from the top of the beam on section D.| 2000 lb2 in.-3 ftD4 in.6 ft6 ft

Answered: Image /qna-images/answer/2f081443-0133-46c8-bdf5-a39d488cf110.jpg

Answered: 1. Determine the maximum tensile and…

Engineering

Civil Engineering

1. Determine the maximum tensile and compressive bending stresses in the beam shown. 4 KNim 200 mm 1= 30 x 10 mm 6m NA

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Explain the meaning of stresses σyy and σxy . Use diagrams to explain

A: Stress is defined as the intensity of force, F, at a point.σ = ∂F/∂A as ∂A → 0,where A is the…

Q: What are the differences between effective stress and total stress? Explain thoroughly.

Q: Is this a frame or a truss? Calculate the cross section of the bar BC if the allowable normal stress…

A: Given:- Allowable normal stress in BC = 165 MPa To determine- a) Is this a frame or a truss? b)…

Q: 4) Explain and illustrate variations of normal stresses everywhere on the bar and state why it is…

A: Given: A bar carrying tensile load and having two holes on the bar. Tensile load=P Due to this load,…

Q: Describe about the deviator stress.

A: - Deviator stress is also know as Principal stress difference, Shear stress, Back pressure stage -…

Q: 19.The total deformation may be regarded as possessing the following a.change in length experienced…

Q: Discuss the classification of cross sections as per the IS 800: 2007 based on yield and plastic…

A: The objective of the question is to understand the classification of cross sections as per the…

Q: How the vibration effecting o the loading stress *

A: Vibrations are caused by a variety of factors, and their impact on structures can be felt by…

Q: 2. Shear stress is caused due to a) Friction b) Temperature c) Pressure d) Volume

A: Shear stress, force tending to cause deformation of a material by slippage along a plane or planes…

Q: Discuss the classification of cross sections as per the IS 800: 2007 based on yield and plastic…

A: The objective of the question is to understand the classification of cross sections as per the…

Q: What is the difference between SIMPLE STRESSES, THIN-WALLED, & STRAIN.

Q: A steel bar is heated from room temperature to 800C while it is free to expand. The bar will…

Q: HW A rigid Sslab weighing boo Ku is Placed uPon two bronzevads and one Steel Vocd Cach of bo00 mm²…

A: Given data, Weight = 600 kN Area of bronze rod Ab = 6000 mm2 Coefficient of expansion for steel αs =…

Q: Explain Unsymmetrical bending and a method to find the stress in an Unsymmetrical section.

A: Unsymmetrical bending takes place in beams. If the moment diagram is unsymmetrical in nature then…

Q: Problem 2 For the beam shown in the figure A) Draw the shear-force and bending-moment diagrams for…

Q: Derive the expression for the stress transformation.

A: It is required to derive the stress transformation equation which is used to find stress acting at a…

Q: (c) In your own words, explain the engineering importance of solving for principal stresses and max…

A: Brief concept introduction- Principal Stresses- These are the normal stresses that act on the…

Q: Mention the layer in between the beam that neither reduces nor elongated after bending.

A: A neutral layer is the layer in between top and bottom fibres of a beam that neither reduces nor…

Q: What is normal stress and it's unit?

A: When a member is loaded by an axial force, stress occurs due to this is known as normal stress.

Q: For the beam loading and geometry shown, determine the following: a. Cracking moment; f = 21 MPa b.…

A: Answer (a) Calculation of cracking Moment We know that cracking Moment is given by Mcr = fr*Iyt fr…

Q: Assume if the shear stress in steel exceeds about 4.00 108 N/m2 the steel ruptures. (a) Determine…

A: Given:- The limiting value of shear stress in steel = 4.00×108 N/m2 The diameter of the steel bolt…

Q: Describe the concept for analysis of stress at a point where external loading causes different…

A: Stress Definition and Analysis – The body offers resistance to the external loading against the…

Q: Why is it important to calculate stress in beams?

A: The stresses are produced in beams when they are subjected to loadings. The stresses that are…

Q: Is the minimum principle stress is always negative?

A: To determine: Whether minimum principal stress is always negative.

Q: Try to give reasons: Why the compressive strength of cubes is greater than cylinders? ie.. Cube…

A: The compression test for concrete will be done on both the type of specimen. First one is 100x100 mm…

Q: Which type of internal bending moment causes the following bending stresses? Y Tancion

A: Under positive Bending moment M is positive Using equation σtensionCompression=MyI

Q: Problem 2 For the beam shown in the figure A) Draw the shear-force and bending-moment diagrams for…

Q: What is meant by strain transformation? Describe two procedures for obtaining stress form Mohr’s…

A: Strain-Transformation equations are supported the pure mathematics of the deformation of deformable…

Q: explain the stress path

A: Stress path is used in a test specimen of soil during loading or unloading to represent the…

Q: Please define the term of anisotropy and bending stiffness.

A: Anisotropy:- In physics, anisotropy refers to the ability to show characteristics with varied…

Q: Unsymmetric bending. Stresses. Neutral axis. Maximum stresses.

A: (a) Unsymmetric bending Pure bending is defined as a state of stress in which the bending moment is…

Q: Show the relationship between axial stress and strain to get the axial deformation

Concept explainers

Planar Stresses

Question

100%

stresses in beams

1.
Determine the maximum tensile and compressive bending stresses in
the beam shown.
4 kN/m
200 mm
-1= 30 x 10 mm
B
6 m
NA
80 mm
2.
For the beam shown in the figure, find the shear stress at a point 30 mm
above the bottom of the beam at section C.
50 mm
|14 kN
1.5 m
B
3 m
100 mm
1 = 19.3 x 10 mm
- NA
A
D
62.5 mm
50 mm
2 m
100 mm

3.
For the beam shown, calculate (a) the maximum bending stress; and (b) the
bending stress at a point 0.5 in. from the top of the beam on section D.
| 2000 lb
2 in.
-3 ft
D
4 in.
6 ft
6 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Maximum bending moment

VIEW

Step 2: bending stress

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the combination of normal and shearing stresses acting on any two mutually perpendicular planes (orthogonal planes) is known, through this what can be determined?
Please solve this question in hand wirting step by step.
Why should the loading be linearly related to the stress or Displacement that is to be determined?
Discuss Stress-Strain Properties
Define the term neutral stress.
A rigid bar, AB, is pinned at point B. Two other bars, AC and AD, are connected to point A to provide support for AB. We are investigating the behavior of this system under a specific load. Key Details: Bar properties: Material: Steel with Young's modulus (Esteel) of 200 GPa and coefficient of thermal expansion (a) of 11.7 x 10^-6 /°C. Cross-sectional area: AC: 1960 mm² AD: 1250 mm² Length: AC: √2 meters (square root of 2 meters) AD: 1 meter Inclination angles: AC: θ₁ (theta 1) = 30° from horizontal AD: θ₂ (theta 2) = 20° from horizontal Load on bar AB: Idealized linearly increasing load with a maximum value of 30 kN/m at point B. Problem Objectives: Determine the internal forces (axial forces) acting within bars AC and AD due to the applied load on AB. Calculate the displacement of point A in both horizontal (dA,x) and vertical (dA,y) directions.If the bar is cooled by 10°C, what would be the: Determine the internal forces (axial forces) acting within bars AC and AD…
Problem 2 For the beam shown in the figure A) Draw the shear-force and bending-moment diagrams for the beam shown in the figure. B) For the composite section, aluminium [E = 70 GPa] bonded to a steel [E = 210 GPa], located at the maximum bending moment, determine: (1) the maximum bending stresses in the aluminium and steel bars. (2) the stress in the two materials at the joint where they are bonded together. K4N/M 2m B 10kN/mm 4m 2m D Steel Aluminum 42mm 20 mm 13 mm
What is the definition of effective stress؟
The following structure has a compression allowable stress of 50 MPa. In the laboratory, it was found that the allowable stress in tension is 5 MPa.
Prove the following relations by considering stresses acting on a material element in triaxial loading.
Describe the Plane Strain and Axisymmetrical Strain.
Explain with a sketch the method which is used to compute the stress ratio.