1. Determine the following for the network shown below*Use Mathematical Approacha. IDb. VGSC. VDSd. Vse. VDGf. gmRDC1HHRsigVsGiven parameters:VDD = 20 VRG = 2 ΜΩRD = 3.3 kRs = 2 kRsig = 500 QRL = 2.2 kΩRGIDSS = 14 mAVp = -5 Vyos = 20 μSC₁ = 0.02 μFC₂ = 1 µFCs = 2.2 µFJ1'RSCSC2VDD30/0-0wRL

1. Determine the following for the network shown below *Use Mathematical Approach a. ID b. VGS c. VDS d. Vs e. VDG f. gm RD C1 Rsig Vs Given parameters: VDD = 20 V RG = 2 ΜΩ RD = 3.3 ΚΩ Rs = 2 kn Rsig = 500 2 RL = 2.2 kΩ RG IDSS = 14 mA Vp = -5 V yos = 20 μS C₁ = 0.02 µF C₂ = 1 µF Cs = 2.2 µF M W RS CS C2 3000 VDD RL

1. Determine the following for the network shown below *Use Mathematical Approach a. ID b. VGS c. VDS d. Vs e. VDG f. gm RD C1 Rsig Vs Given parameters: VDD = 20 V RG = 2 ΜΩ RD = 3.3 ΚΩ Rs = 2 kn Rsig = 500 2 RL = 2.2 kΩ RG IDSS = 14 mA Vp = -5 V yos = 20 μS C₁ = 0.02 µF C₂ = 1 µF Cs = 2.2 µF M W RS CS C2 3000 VDD RL

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

@)A communic ation system is operating at 1KHZ AKllz sapply frequeney.A paralle farallel resistance. capacitance bridge is used to determine the resistive and capacitive components of the communication system. The bridge at c1 0.2UF is balanced R,=L2,Rz=6KSZ gRy= LIK2. Delermine unknown resistive nnd capacitve and dissipation factor. %3D the Components
No. 1 2 3 4 5 6 7 8 9 10 Mnemonics MOV A, # 0A9h RL A RL A SWAP A CLR C RRC A SWAP A CLR C RRC A SWAP A Operation
Q1/D:-The Si transister B 100 , Rc = 2 ka and Vcc 12V, VCEQ = Vcc/2 a-determine RF. b-find RE that added to the Si transister. RC Cc Rp Rs RL Cc
Circuit theory
Plot the dc bias line for this circuit. www11 R₁ 1.5 ΜΩ R₂ 1.5 ΜΩ VGS (V) +30 V RD 1.1 ΚΩ 2N5459 www11 Rs 10 ΚΩ Minimum and maximum curves are from the datasheets. ID (mA) 16 -12 -10 Qmax 14 1 L L 1 -8 -6 -4 -2 12 10 8 6 4 Qmin Hó VG Rs 1 2 = 1.5 mA 4 1 6 8 10 12 14 16 18 VG
Various parameters of Schering bridge are given as follows. The voltage supply of 2 kHz is connected to terminals A and C and detector to points B and D. Arm AB comprises the unknown Resistor R1 and capacitor C1. Arm BC consists of resistor R2 of 18k 2. Arm DA consists of capacitor C2 of 0.06 µf. Arm CD has R3 of 1.5k2 and C3 of 2nf are in parallel. Calculate (i) the capacitance (C1) (ii) the equivalent series resistance (R1) and (iii) dissipation factor. Also draw the schematic diagram.
1. CRTAL -? 2. QnnAL = ? 3. Q2 4. V7 -? 5. V3 : ? : ? (2) 2 AF TCH=ZMF Ta- 50V CG 2m F i. TOTAL CAPACITANCE G TITAL CHARGE ? 2. ENEREY ORED IN A CRCUT?
Apply the junction rule to junction b in Figure. Is any new information gained by applying the junction rule at e? (In the figure, each emf is represented by script E.)
Vbe=0.7v find Vb, Ve,Ie,Ib,Icq,Vce
5. Vs=4.0 V, VD=8.0 V, ID = 0.18 mA, and VGs = 0.92 V. VDD=12V a. Find Rs RGI Roz 2 Ro M Vp Vs b. Find RD c. Find VG.
B 72 M @ Quiz.pdf X Quiz:-A p-channel JFET has a VGSOFF=+6v 1)What is ID if VGs has value half VGSOFF 2)What is ID if VGs=3v
Explain simply how they do!