1. Consider the transistor characteristics of Figure below. (a) Are these the characteristics of a JFET, d-mosfet, or e-mosfet? (b) Make a table of the given Vgs values and the corresponding la(sat) Values. Also include a column in the table giving vId(sat), (c) Make a plot of vld(sat) versus Vgs. Find the slope and y- intercept of the pllot and use these to determine values for K and V, in the model equation Eq. (5.3). 10 9. 8 7 -0.5 6. la(mA) 5 4. -1.0 3 -1.5 -2.0 --2,5 8 10 12 14 16 Vas (V)

1. Consider the transistor characteristics of Figure below. (a) Are these the characteristics of a JFET, d-mosfet, or e-mosfet? (b) Make a table of the given Vgs values and the corresponding la(sat) Values. Also include a column in the table giving vId(sat), (c) Make a plot of vld(sat) versus Vgs. Find the slope and y- intercept of the pllot and use these to determine values for K and V, in the model equation Eq. (5.3). 10 9. 8 7 -0.5 6. la(mA) 5 4. -1.0 3 -1.5 -2.0 --2,5 8 10 12 14 16 Vas (V)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Assignment Goal: You are to research for different methods of biasing BJT circuits, and to choose and describe one of these methods in details in order to design a single stage common emitter or common base amplifier circuit. The report should have the following sections and cover the points listed below: 1. An overview about the purpose of biasing, and different methods of biasing. 2. Design method of your own simple amplifier circuit. 3. Calculations and analysis (including all DC and ac analysis: operating point, current and voltage gains, input and output resistances, voltage waveforms at all nodes in the amplifier circuit..., etc). 4. Simulation results. (Use BC107 for the BJT in your simulation). 5. A comparison between calculated and simulated results, and a conclusion. Support your design and results with explanation and parametric studies in details. For example, in your designed circuit, vary the value of the collector resistance Rc to change the mode of operation of the…
Why is there a difference in the beta value? (D. C) and the beta (A. C) value in some transistor output characteristic schemes.
1. To use the Bipolar Junction Transistor (BJT) as a small signal amplifier it must be biased in this region: A. South Park region B. Spatial interface region C. Inverse Thevenin region D. Linear or active region
Bipolar junction transistors (BJTS) are considered “normally-off" devices, because their natural state with no signal applied to the base is no . .between emitter and collector, like an open switch. *
I need the answer at 15 minute
Question 6 A large signal circuit model for a MOSFET consists of a dependent current source in parallel with an output resistance, ro, where ro can be expressed as 1/1lp or VA/ID. True False
a) Find the operating point current and voltage values of the non-linear element, in resistor R3 Calculate the voltage generated by the constant sources. b) Draw the circuit equivalent by linearizing the nonlinear element at the operating point. c) Using linearized equivalent small signal source j (t) to occur at R3 resistance calculate the voltage brought by it and give the expression of the VR3 voltage (constant sources and small sign sum of voltages generated by the source). E1=A=3 E2=B=8
Problem 1: Consider the circuit shown below. The transistor parameters are Kn1 = 0.5 mA/V2 , Kn2 = 0.2 mA/V2 , VT N1 = VT N2 = 1.2 V, and λ1 = λ2 = 0. The quiescent drain currents are ID1 = 0.2 mA and ID2 = 0.5 mA. (a) Determine the small-signal voltage gain of the given multistage amplifier. Answer: -6.14. (b) Calculate the small-signal output resistance Ro. Answer: 1.32 kΩ. Problem 2: The transistor parameters for the given circuit are β1 = 120, β2 = 80, VBE1 (on) = VBE2 (on) = 0.7 V, and VA1 = VA2 = ∞. (a) Determine the quiescent collector current in each transistor. Answer: IC1 = 2.253 mA, IC2 = 69.73 mA. (b) Find the small-signal voltage gain Av = vo/vs. Answer: 0.99. (c) Determine the input and output resistances Rib and Ro. Answer: Rib = 467.6 kΩ, Ro = 0.512 Ω
c) Figure 2.3 shows the circuit diagram of a typical npn BJT common emitter amplifier. The values of RB1-30 kOhm, RB2=10.XY kOhm, Rc-3.XY kOhm, Ic=2.XY mA and Vcc=24 V. If the transistor current gain 3 = 50 determine using the full analysis and assuming VBE = 0.7 V the value of RE, hence identify the location of the Q-point (Ic, VCE, IB and VBE). Now sketch the AC circuit model of this amplifier and determine the value of the ac open circuit voltage gain Av and the ac short circuit current gain Ai. (Assume that Vth = 26 mV). Vin RB1 Cin lin RB2 -10 Rc VB RE + Vcc Vc Cout VE www li Figure 2.3 Vout Ce ¡out x=1 y=7
In single transistor amplifier design, it is observed that the voltage gain will always decrease as the load resistance increases. True False The saturation region of MOSFET indicates that the drain current no longer depends on the source-drain voltage while the saturation region of BJT indicates that the collector current no longer depends on the collector-emitter voltage. True False A bipolar junction transistor can be connected to behave like a diode while a field effect transistor can not be connected to behave like a diode. True False A voltage follower circuit is usually designed to have the power gain slightly less than 1 with any passive load. True False A clipper circuit regulates DC voltage input while a clamp circuit regulates AC voltage input. True False
In the following problem we want to calculate an N-type MOSFET transistorparameters when body is connected to the source. The W/L = 10 for the device,and ignore channel length modulation. a)Based on triode and saturation equations that you learned in the class, plotdrain current versus drain voltage, when source is grounded and Vgs = 0.5,1, and 3V. Sweep the drain voltage from 0 V to 3 V. This plot is calledOutput characteristics of a transistor. Highlight the point where transistorsregion is switched from triode region into saturation.
Please solve all and show all the steps in detail