FOLLOW UP QUESTIONS: BIPOLAR JUNCTION TRANSISTOR (BJT) SOLVE FOR a.) IC(sat) b.) VCE(off) CONSTRUCT A DC LOAD LINE SHOWING THE VALUES: c.) IC (sat) d.) VCE (off) e.) ICQ f.) VCEQ

Q: If the transistors are matched with Kn-0.2MAV and V-2.15V, what is lout if the resistor value is 3.4…

A:

Q: The breakdown voltage of a lot of transistors is assumed to follow a normal distribution. Ten…

A: Cpk is a measure of a system's output that how perfectly it meets the both upper and lower limit.

Q: Electronic 2 : For the network in the figure: a) Obtain the necessary equation for IB Base current…

A: Solution - (a) The given circuit is shown below,

Q: 1-Write the characteristics of NTC.? 2-Draw the Characteristic curve of PTC.?

A: NTC and PTC

Q: Describe step by step how MOSFET works and its applications.

A: MOSFET is Metal Oxide Semiconductor Field Effect Transistor. It is a voltage-controlled device. It…

Q: During turn-on and turn-off of a power transistor, the current-time and voltage-time relationships…

A:

Q: 1) what is the Voltage & Current rating ofTriode for Alternating Current (TRIAC)  2) 5. Are the…

A:

Q: Justify, three terminal devices are far more useful than two terminal ones. Describe in detail how…

A: The diode is a two terminal device. A diode has two electrodes and one PN junction The BJT and FET…

Q: Transistor acts as an open circuit in Cut off region... In this region, both the junctions EB…

A: The transistor act as open circuit in cutoff region because both the junctions that is emitter base…

Q: is problem is AC analysis problem. DC analysis is not needed to answer the question. A) Convert this…

A: We need to draw complete circuit for bypass  comman emitter Amplifier , we also need to draw small…

Q: This course A bipolar junction transistor operating in saturation mode is used as: Select one: O a.…

A:

Q: . A BJT transistor to work as a switch must be biased in the region of: Select one: a. cut b.…

A: 1. A BJT transistor to work as a switch must be biased in the region of Saturation region and…

Q: What are the differences between MOSFET transistor and BJT transistor? (included advantages and…

A: BJT MOSFET PNP or NPN and current controlled device N-type or P-type and voltage controlled…

Q: 12. If a transfer function has poles at (-1, 2) and (-1, -2) and a zero at (0, 0), 1, what is the…

A: GivenPoles at  and Zero at To Find(a) Sketch  on the interval (b) Approximate highest value of  when…

Q: (i) Briefly explain the TWO (2) classification of power converters with the converter examples. (ii)…

A:

Q: In your own words, briefly describe the basic operation of an E-MOSFET.

A: MOSFET full form is Metal oxide semiconductor field-effect transistor.

Q: What is the W/L ratio of M1 required to achieve a gain of 26 dB if η = 0.2 and(W/L)2 = 4/1?

A: Given: To determine the W/L ratio of M1 required to achieve a gain of 26 dB if η = 0.2 and (W/L)2 =…

Q: In a Bipolar Transistor define the quantity a or hFB. How is the device structure of the npn Bipolar…

A: A Bipolar Junction Transistor (BJT) is a three-terminal semiconductor device that consists of two…

Q: Compare the ac circuit characteristics of the common-source, source-follower, and common-gate…

A: The table is shown below which represents the characteristics for a common source, source follower…

Q: IGBT is a short form of Insulated Gate Bipolar Transistor, combination of Bipolar Junction…

A: The comparison table on above characteristic is given below

Q: Q) A solid insulating sphere with radius 0.45 m carries a net charge of 0.25 nC. Find the magnitude…

A: Note :- when electric field is calculated outside the surface of the sphere then then the sphere is…

Q: State the advantage of using transistors in place of resistors in MOSFET inte- grated circuits.

A: The transistors in the integrated circuits are used for replacing the resistor, the reason behind…

Q: 4. (a) Draw the IV characteristics of a thyristor and explain what the importance is of the…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: c) Discuss the differences between Insulated Gate Bipolar Transistor (IGBT) and Power Metal Oxide…

A: Differences between Insulated Gate Bipolar Transistor (IGBT) and Power Metal Oxide Semiconductor…

Q: (1) Using a common-emitter transistor configuration circuit discuss une Imput, output and transfer…

A:

Q: Explain the working principle of a metal oxide field effect transistor (MOSFET).

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: Consider one Design or applications of MOSFET (can be as a small signal amplifier and digital…

A: MOSFET stands for Metal Oxide Semiconductor Field Effect Transistor. MOSFET is a voltage controlled…

Q: lustrate operational regions of MOSFET using its voltage-current characteristics.

A:

Q: 3) Explain the functional principle of an ideal MOSFET and which simplifying assumptions are made by…

A: A MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor) is a type of transistor commonly used…

BJT (Bipolar Junction Transistor)

A BJT is a semiconductor device with 3 terminals that consist of a p-n junction diode that can amplify the signal or current. It is a current-controlled device. The three BJT terminals are base, collector, and emitter. The BJT works with the charge carrier, the two type of carriers in the BJT are holes and electrons, the charge carriers flow by the process of recombination. The signal to be amplifier is generally given as the input at the base terminal and an amplified form of it is available at the collector terminal.