1. Consider a branching pipeline system with diameter of 3ft where each pipe has a length of 5000ft. Assume friction factor =0.02 and that both pumps are identical. Pump characteristics are shown in the table below. Assume water surface elevations for the reservoirs are A=80ft, D=94ft. If the discharge in pipe BC is 20ft³/s (with flow from B to C), what is (A) discharge in AB and BD? (b) Water surface elevation in reservoir C? and (C) Head added by each pump?

1. Consider a branching pipeline system with diameter of 3ft where each pipe has a length of 5000ft. Assume friction factor =0.02 and that both pumps are identical. Pump characteristics are shown in the table below. Assume water surface elevations for the reservoirs are A=80ft, D=94ft. If the discharge in pipe BC is 20ft³/s (with flow from B to C), what is (A) discharge in AB and BD? (b) Water surface elevation in reservoir C? and (C) Head added by each pump?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

the marked answers are correct. Expalin the steps
8. Water is flowing in a 100 mm diameter Mild Steel (MS) pipe of length 180 m as shown in the figure. The reservoir water level remains constant. Determine the flow rate. Use the following methods: (a) Darcy Weisbach formula with loss coefficient method, (b) Darcy Weisbach formula with effective pipe length method, (c) Hazen William's formula with loss coefficient method, and (d) Hazen William's formula with effective pipe length method. (Ans.: 28.27 liter/s, 28.33 liter/s, 32.04 liter/s, 32.67 liter/s) EL85 m EL = Elevation Gaie valve Butterfly valvé opened EL50 m
The three reservoirs, A, B and C are connected by pipelines A, B and C respectively which meets at the junction X. The elevation of reservoir A is equal to 300 m while that of B is 285 m. The discharge flowing out of reservoir A is 1.4 cu.m/sec. (Pipes, Diameter, Length, Friction factor "f")A, 800 mm, 1500 m, 0.0157B, 600 mm, 450 m, 0.0162C, 450 mm, 1200 m, 0.0177 (a) Compute the rate of flow in reservoir B in cu.m/sec. (b) Compute the rate of flow in reservoir C in cu.m/sec. (c) Compute the elevation of Reservoir C in meters.
Question 7 (Parallel pipes) Two reservoirs are connected by two parallel pipelines with diameters of 0.8m and 0.6m as shown in Figure 8. The pipelines are both 3 km long with a value of 0.03. The combine discharge through the pipelines must be at least. Pipe 2 Pipe 1 Figure 8 a) When the total discharge is, what is the flow rate in the individual pipeline? b) What is the minimum difference in the elevation of the surface water level in the two reservoirs required to maintain a flow of through the pipelines?
Find the headloss (ft) in a pipeline consisting 98ft. Of 2.9 inches in diameter. The flowrate is 1.6 ft^3/s kerosene. Use manning’s formula,n=0.014 Express in whole number
Answer Question 6: the marked choice is the correct answer.
pls do not round off the decimal. only in the final answer
need complete solution with illustration
PLEASE PROVIDE DETAILED EXPLANATION AND SOLUTION. ANSWER CORRECTLY
A 1m diameter commercial steel pipe that is 2km in length carries water (20°C) fromreservoir A to reservoir B. The difference in elevation between the two reservoir surfaces is 150m.Compute the discharge through the pipe. (Solve by hand with Moody Chart; utilize Darcy-Weisbach)
Please solve it using the equation given
Three reservoirs A, B, and C are connected by pipeline 1, 2 and 3 respectively which merges at a junction X. The elevation of reservoir A is 350 m and that of B is 290m. The rate of flow from A is 1.5 m^3/s. (See the table) 1. Compute the rate of flow in reservoirs B and C. Pipes Diameter Length Friction factor “f” 1 825 mm 1500 m 0.0155 2 650 mm 450 m 0.0165 3 450 mm 1200 m 0.0175