1. Consider a 5-m-high, 8-m-long, and 0.22-m-thick wall whose representative cross section is as given in the Fig. The thermal conductivities of various materials used, in W/m-°C, are k = kr = 2, KB = 8,kc=20, KD = 15, and k = 35. The left and right surfaces of the wall are maintained at uniform temperatures of 300 °C and 100 °C, respectively. Assuming heat transfer through the wall to be one-dimensional, determine: (a) the rate of heat transfer through the wall; (b) the temperature at the point where the sections B, D, and E meet; and (c) the temperature drop across the section F. Disregard any contact resistances at the interfaces. 300°C 1 cm C A 4 cm B 4 cm 4 cm D C 6 cm 5 cm 6 cm E| F 10 cm 6 cm 100°C 8 m

1. Consider a 5-m-high, 8-m-long, and 0.22-m-thick wall whose representative cross section is as given in the Fig. The thermal conductivities of various materials used, in W/m-°C, are k = kr = 2, KB = 8,kc=20, KD = 15, and k = 35. The left and right surfaces of the wall are maintained at uniform temperatures of 300 °C and 100 °C, respectively. Assuming heat transfer through the wall to be one-dimensional, determine: (a) the rate of heat transfer through the wall; (b) the temperature at the point where the sections B, D, and E meet; and (c) the temperature drop across the section F. Disregard any contact resistances at the interfaces. 300°C 1 cm C A 4 cm B 4 cm 4 cm D C 6 cm 5 cm 6 cm E| F 10 cm 6 cm 100°C 8 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Consider a long bar of square cross section (0.8 m to the side) and of thermal conductivity 2 W/m-K.…

A: To find: The midpoint temperature of the bar, heat transfer rate between the bar and the fluid per…

Q: Consider a 1m long, 3.5mm diameter wire, with a thermal conductivity of 20 W/mK. If the wire has a…

A: Given data: ◆ The length and diameter of the wire: L = 1 m , d = 3.5 mm = 0.0035 m ◆ The thermal…

Q: H +x L→∞0 B The temperature at the base is 498 K, and the temperature of the surrounding fluid is…

Q: The compartment below is used as a freezer of refrigerator compartment. Inner wall is at -15 C and…

A: Solution:

Q: 3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ =…

Q: A 1.69 m wide by 1.06 m high metal plate must be insulated to prevent contact burn injuries. If the…

Q: The composite wall of a furnace consists of three different materials, two of which have known…

A: Given:The thermal conductivity at A is The thermal conductivity at C is The thickness at A is The…

Q: A plane wall of an oven with an insulation coating is attached to an insulated wall. The thermal…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: Ponder upon a 5-m-high, 8-m-long, and 0.22-m-thick wall whose representative cross section is as…

Q: The inside surface temperature of a glass oven door (0.5 m x 0.5 m x 0.001 m) is 180°C, the outside…

Q: Two bars A and B, each of length 2m and cross sectional area 1m^2, are placed end to end. Their…

A: Given Thermal conductivity, kA = 339 W/mK kB = 837 W/mK…

Q: A typical exterior frame wall (made up of 60 mm × 120 mm studs) of a housecontains the materials as…

A: Given, inside room temperature , Ti = 21* C outside temperature , To = - 6* c. exposed area of the…

Q: A dormitory at a large university, built 50 years ago, has exterior walls constructed of L, =…

Q: HEAT TRANSFER A 30 ft. long and 2 inch nominal diameter and outside diameter of 2.375 in pipe is…

A: GivenL=30ftdi=2indo=2.375 int=1ink2=0.0375 Btu/hr ft FoT1=380oFT2=80oF

Q: (a) The heat transfer rate function. (b) The rate of change of energy stored in the wall. (c) The…

A: For solution refer below images.

Q: 3. Consider a plane composite wall that is made of two materials of thermal conductivities ka = 205…

Q: Plaster Insulation Brick Inside Air Outside Air le ra A particular house wall consists of three…

A: CONDUCTION COVEVECTION HEAT TRANFER THROGH A COMPOSITE LAB Heat move through a plane mass of…

Q: A dormitory at a large university, built 50 years ago, has exterior walls constructed of L, =…

A: Answer: (a) The heat flux through the original walls is 75.51 W/m2. (b) The heat flux through the…

Q: A 6 in thick concrete wall, having thermal conductivity k =0.50 Btu/h-ft-º F, is exposed to air at…

A: Given:thickness of wall, t=6 in =0.5ftThermal conductivity, k=0.50 Btu/h.ft.°FT1=70°FT2=20°Fhi=2.0…

Q: A 1 m x 1 m plate made of brass (k = 70 W/mK) with a thickness of 5 cm is used a heating element…

A: given; ⇒conductivity (k)=70w/mk⇒ power (q)=1900w⇒at x=5cm ,temperature (T)=2500c=523k

Q: Electrical current flows through a cylindrical cable with a diameter of d = 4 mm generating thermal…

Q: A plain wall having a thickness of 100 mm and a thermal conductivity of 15 W/m.K exhibits a heat…

Q: 4. A lumped system has a Bi number equal to 0.05. It is made of a material with density of 1300…

Q: A plane wall of an oven with an insulation coating is attached to an insulated wall. The thermal…

A: Given that, Thermal conductivity of insulated coating, ki=0.1 W/m.K,Thickness of insulation coating,…

Q: The composite wall of an oven consists of three materials, two of which are of known thermal…

A: Given:kA=25 W/m.KkC=60W/m.KLA=0.40 mLB=0.20 mLC=0.20 mTs,o=20oCTs,i=600oCT∞=800oCh=25 W/m2.KFind:The…

Q: The two surfaces of a 1.0-cm-thick plane wall are at 10°C and 45°C, and the heat transfer rate is…

A: Thickness of the surfaceTemperatures:Heat transfer rate

Q: The rear window of a car is defrosted by the passage of warm air on the internal surface. If the…

Q: A furnace wall comprises three layers of thickness 250 mm, 100 mm, and 150 mm with thermal…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

1. Consider a 5-m-high, 8-m-long, and 0.22-m-thick wall whose representative cross section is as
given in the Fig. The thermal conductivities of various materials used, in W/m-°C, are k = kr = 2,
KB = 8,kc=20, KD = 15, and k = 35. The left and right surfaces of the wall are maintained at uniform
temperatures of 300 °C and 100 °C, respectively. Assuming heat transfer through the wall to be
one-dimensional, determine:
(a) the rate of heat transfer through the wall;
(b) the temperature at the point where the sections B, D, and E meet; and
(c) the temperature drop across the section F.
Disregard any contact resistances at the interfaces.
300°C
1 cm
C
A 4 cm
B
4 cm
4 cm
D
C 6 cm
5 cm
6 cm
E|
F
10 cm 6 cm
100°C
8 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Calculation of thermal resistance of each section

VIEW

Step 2: Calculation for equivalent thermal resistance

VIEW

Step 3: Heat flow through wall is calculated

VIEW

Step 4: Temperature at meeting point of B,D and E

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider modeling a temperature sensor as a sphere having a thermal conductivity of 91 W/m-K, a density of 8900 kg/m³, and a specific heat of 444 J/kg-K. The sensor is in an environment where the heat transfer coefficient is 100 W/m²-K. Determine the maximum allowable diameter of the sensor if the 90% response time to a step-change in the fluid temperature, T∞, must be: • 10 second • 1 second . 0.01 second
nt Select D 0 261.40 ( 142. СС 60 Home Insert Space 300c° Insert Draw View Exercise 5 the bobul 3-75 Consider a 5-m-high 8-m-long, and 0.22-m-thick wall whose representative cross section is as given in the figure. The thermal conductivities of various materials used, in W/m-K, are k, = kp = 2, kg = 8, ke=20, kp = 15, and kg = 35. The left and right surfaces of the wall are maintained at uniform temperatures of 300°C and 100°C, respectively. Assuming heat transfer through the wall to be one-dimensional, determine (a) the rate of heat transfer through the wall; (b) the temperature at the point where the sections B, D, and E meet; and (c) the temperature drop across the section F. Disregard any contact resistances at the interfaces. RA p Re RB RC Ro RE ******** ве R=RA + ROBC+R DE + Rr ****** 300°C Ri 1000 1 сгу اللينفب اللوطن يمني نفتي المتريال 5 cm | +100 cm оста 6 cm Pencil + 100°C 0.12 M 10 C
A temperature difference of 85oC exists across a fibreglass insulation layer 13 cm thick, for which k = 0.035 W/mK. Calculate the heat transferred through the fibreglass per hour per unit area.
Consider a wall that is 5 m high, 8 m long, and 0.22 m thick. The thermal conductivities of the various materials used, in W/m °C, are kA = kF = 2, kB = 8, kC = 20, kD = 15 and kE = 35. The left and right surfaces of the wall are maintained at uniform temperatures of 300 °C and 100 °C, respectively. If the heat transfer through the wall is one-dimensional, determine (a) the rate of heat transfer through the wall; b) the temperature at the point where sections B, D, and E meet, and c) the temperature drop across section F. Disregard any contact resistances between the interfaces.
Consider modeling a temperature sensor as a sphere having a thermal conductivity of 91 W/m-K, a density of 8900 kg/m³, and a specific heat of 444 J/kg-K. The sensor is in an environment where the heat transfer coefficient is 100 W/m²-K. Determine the maximum allowable diameter of the sensor if the 90% response time to a step-change in the fluid temperature, T∞, must be: • 10 second • 1 second . 0.01 second
Temperature distribution of a wall is given as T(x) = -100x + 50 and the cold surface is exposed to a convection environment at temperature of 20 °C. If the wall thickness is 10 cm and the conductivity is 1 W/mK what is the convection coefficient between the cold surface and the environment?
Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 800 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 10 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = Answer kJ / hour. b. Temperature between insulation layers. = Answer ° C.
The composite wall of an oven consists of three materials, with thermal conductivity, KA = 20 W/ m. kg = 30 W/ m. K, kc = 50 W/m. K, and known thickness, LA =30 cm,, LB =20 cm and Lc = 15 cm. Under steady- state operating conditions, measurements reveal an outer surface temperature of Tso =20°C, an inner surface temperature of Tsi = 600°C. The inside and outside convection coefficients are 25 W/m2. K and 15 W/m2. K. The wall repeats itself every 25 cm distance in the vertical direction and if the wall is 1-m deep and 0.25-m high, then assume an area of 0.25m2 for all your calculations. Find the total resistance. T- 600°c T 20°c Air T, h Select one: O a. 10.525°C/W O b. 5.526°C/W O c. 0.526°C/W
A hot water pipe is used for domestic applications is insulated with a layer of calcium silicate. If the insulation is 25 mm thick and its inner and outer surfaces are maintained at Ts,1 = 800 K and Ts,2 = 400 K, respectively. The outside diameter is 0.12 m. Calculate the heat loss per unit length of the pipe. Given the thermal conductivity of calcium silicate insulation equals to 0.09 W/m.K.