1. Calculate Total Solids (TS) and Total Dissolved Solids (TDS) in mg/L from the following data ofa water sample.Sampleamount(mL)150TS (mg/L) =Wt. ofBeakerl (g)106.5023Wt. of Beaker1 +solids withoutfiltration of sample106.5603Wt. ofBeaker2 (g)120.5721A TDS (mg/L) =Wt. of Beaker2 +solids after filtrationof sample (g)120.6123

Sample amount V = 150 mL Weight of beaker 1 (W1) = 106.5023 gm Weight of beaker 1+ solids without…

Answered: 1. Calculate Total Solids (TS) and…

Engineering

Civil Engineering

1. Calculate Total Solids (TS) and Total Dissolved Solids (TDS) in mg/L from the following data of a water sample. Sp

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 5. The permeability of 160-acre formation drained by a single well is 15 mD. The well is heavily…

A: we have to determine the average permeability of the drainage area

Q: Determine whether the following beams are Statically Unstable Structure, Statically Determinate…

A: Structure is a assembly of the vertical and horizontal member. Stability means the structure should…

Q: The dam on Hydaway Lake on Liberty Mountain (not really sure if a dam exists) has the potential to…

A: Assume the datum to be horizontal passing through B. The discharge at B, Q = 300ft3/sec The specific…

Q: For the timber column shown in the two figures below, E 12 GPa and the allowable stress for…

A: Allowable compression stress in parallel = 9 MPa Young's Modulus, E = 12 GPa Depth of the column = 2…

Q: Design a 13.34 ft simply supported solid one-way slab system to carry a uniformly distributed…

A: The span length = 13.34 ft The magnitude of dead load = 140 psf (excluding self weight) The…

Q: 8. Draw the axial force influence lines for the members CD, HD, and HI. D B E A G H I J F · 30 ft…

A: A truss with support and asked to draw the Axial force influence line diagram for the members CD, HD…

Q: ▪ Determine the Rankine active force, Pa, per unit length of the wall and the location of the…

A: Rankine's active force is given by the area of active pressure diagram. In order to draw the active…

Q: 1- Find the final consolidation settlement 2- Having the final consolidation settlement of (20) cm,…

A: This question is from Consolidation in Geotechnical Engineering.

Q: 10 25k 10'

A: The below cantilever beam is given;

Q: SITUATION - For the truss shown, calculate the stresses in members CE, DE, and DF. The…

A: Cross sectional area of all member (A) = 1.8 in.2 Determine the stresses in member CE, DE and DF.…

Q: Figure 1 shows a simply supported beam with a concentrated force P applied at the mid-span, B. Given…

Q: 5. Locate the centroid of the plane area shown below. - 300 mm 150 mm 150 mm 75 mm 100 mm 100 mm

Q: A robotic arm made from steel has a length of 1.524 m, a breadth of 0.102 m, and a height of 0.1524…

A: Length- L=1.524 m Moment of inertia I=3x10-5 m4 Robotic link mass W=1200 kg/m, Payload P=444.82 kg.…

Q: A3 ft x 3 ft square footing is to be placed over the following soil profile to support 18-kips…

Q: A 75 mm D B Determine the force in member BD and the co C.

Q: 1. A 5-m beam simply supported at the ends carries a concentrated load of 90 kN at midspan. Select…

Q: For material testing,Take one destructive and one non-destructive test and explain how both test…

A: Material testing is a crucial aspect of engineering as it helps determine the suitability and…

Q: A reinforced concrete wall footing is founded 6 ft below grade. If the footing supports a…

Q: Design the section below as a doubly reinforced beam for resisting the ultimate positive moment of…

A: We are given Ultimate Positive Moment Mu = 425 KN-m We know that Nominal Moment capacity is given…

Q: A 3 ft x 3 ft square footing is to be placed over the following soll profile to support 18kips…

Q: A reverse curve connects two converging tangents intersecting at an angle of 30 degrees. The…

A: The distance of this intersection from the PI of the curve is 150 meters The azimuth of the common…

Q: A raft of size 4 m-square carries a load of 400 kN/m2. Determine the vertical stress increment at a…

A: Given: The size of the square raft is 4 m. The load is 400 kN/m2. The depth is 5 m.

Q: P8.11. Determine the horizontal and vertical deflection of joint C of the truss in Figure P8.11. In…

A: Deflection : In structural engineering, deflection is the diploma to which part of a structural…

Q: The principal stresses at a point are 20 (tensile) and o (compressive), and the stress at elastic…

Q: The horizontal layout of new cast iron pipes is as shown in the figure. Coefficient of friction is f…

A: Total head loss from A to D is 30ft. f = 0.02 Determine the discharge in pipe-4 (Q4).

Q: A 20 m long steel rod is at a temperature of 20°C. The rod is heated so that temperature rises by…

A: Length of steel rod = 20 m at temperature = 20oC Final temperature rises by 50oC Extension upto 14…

Q: SITUATION F. A reinforced concrete beam 250mm wide and 450mm high carries an ultimate moment of 202…

Q: Q.2: Closed traverse ABCDE:The lengths of AB = 97.32 m, DE= 112.56 m and EA =107.92 m. The bearing…

A: Solution, whole circle bearing of line ; AB =θ 46*37' (Degree = *) θBC = 180* - 82*40' =…

Q: For a highway curve with Da = 5°00', I = 20°30', and Pl station = 63 +25.53 ft, calculate the…

Q: 4. Use the method of joints to determine the internal forces in each member of the truss. The…

A: Method of joints is a method of structural analysis that is used to determine the unknown forces in…

Q: b) List at least three types of pavement distress for flexible and rigid pavement, respectively.

A: List at least three types of pavement distress for flexible and rigid pavement, respectively.

Q: P8.7. Determine the value of the force P applied to joint C of the truss in Figure P8.7 i deflection…

Q: The floor system of a residential building consists of 125mm thick reinforced concrete slab (unit…

Q: What is temperature susceptibility of asphalt binder? What is the difference between asphalt cement…

A: Context: Asphalt binder, asphalt cement, asphalt emulsion

Q: A B C -5m-10m 10m 10m D

A: A we have to compute the ordinate of influence line

Q: Determine the support reactions and member forces of the trusses shown.

Q: A raft of size 4 m-square carries a load of 400 kN/m2. Determine the vertical stress increment at a…

Q: 3. Use the method of joints to determine the internal forces in each member of the truss. The…

Q: dry density for a soil sample having specific gravity of 2.7 and optimum moisture content of 16% (a)…

A: Specific gravity = 2.7 Optimum moisture content = 16 % This is a problem of Soil mechanics where we…

Q: In fine sand aquifer region, design a well to get 10 l/sec yield under the depression head of C 2.5…

Q: P8.10. (a) Compute the horizontal displacement of joint B produced by the 240-kN load in Figure…

Q: Problem #4 Determine the horizontal and vertical components of the resultant forces that the water…

A: Given data in question Radius 2 m Width 1.5 m Angle 45° To find out Horizontal and vertical…

Q: An asphalt concrete mix has a density of 2370 kg/m3 at an asphlalt content of 5.8%. The asphalt…

A: Density of asphalt concrete mix is 2370 kg/m3 Asphalt content of 5.8% The asphalt absorption is…

Q: On a vertical photograph of flat terrain, section corners, which are a nominal 1-mi apart, appear a…

Q: Find the normal stress, shear stress, and bending deformation of the beam. For the cross-sectional…

Q: 086) Ordinates of a 2-hour unit hydrograph are given in the table below. Using these, derive a…

A: Derive 4-hr UH using S-curve method.

Q: Figure Q2 shows a 2-dimensional truss. The area of each member is equal to A. The modulus of…

A: Find: (a) Degree of freedom (b) Transformation matrix (c) Global stiffness matrix

Q: a) Without considering the vertical spring, determine the stiffness coefficient of the simply r==…

Q: Use the stress transformation equations to determine the state of stress for the element shown if it…

Q: | 5% in = 12 ft 8 in 5 in (a) 4-PL3/8 X 5 Fy-36 ksi

A: Given data: Section- PL38x5 Effective length, Le=12 ft 8 in The design strength can be calculated…

Concept explainers

Fluid Materials

In general terms, anything that flows can be termed as a fluid. In other words, a fluid is any substance that cannot resist shear forces and deforms continuously under the application of external shear forces. Fluid materials differ completely from solid materials such as metals and alloys. For instance, if we consider two infinitesimally small cross-sectional areas of fluid materials and solid materials, and apply shear forces to these elements, both the elements will undergo deformation. Upon releasing the shear force, the element of the solid materials will regain its original orientation, but the element of the fluid materials will keep on deforming continuously under the action of the shear force.

Question

1. Calculate Total Solids (TS) and Total Dissolved Solids (TDS) in mg/L from the following data of
a water sample.
Sample
amount
(mL)
150
TS (mg/L) =
Wt. of
Beakerl (g)
106.5023
Wt. of Beaker1 +
solids without
filtration of sample
106.5603
Wt. of
Beaker2 (g)
120.5721
A TDS (mg/L) =
Wt. of Beaker2 +
solids after filtration
of sample (g)
120.6123

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculation of Total solids

VIEW

Step 3: Calculation of Total suspended solids

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solids analysis is one of the most widely used parameters for assessing water quality. Use the following data to determine (a) total solids (TS); (b) volatile solids (VS); (c) dissolved solids (DS); (d) total suspended solids (TSS), and (e) total volatile suspended solids (TVSS) all in mg/L. A sample volume of 150 ml was used in performing all solids analyses. Tare mass of evaporating dish = 24.3520 g Mass of evaporating dish plus residue after evaporation @ 105°C = 24.3970 g Mass of evaporating dish plus residue after ignition @ 550°C = 24.3850 g Mass of Whatman filter and tare Mass of Whatman filter and tare after drying @ 105°C Residue on Whatman filter and tare after ignition @ 550°C = 1.5103 g 1.5439 g 1.5199 g
4) Solids analysis is one of the important parameters for assessing water quality. Use the following data for calculating total solids (TS), volatile solids (VS), dissolved solids (DS), total suspended solids (TSS), and total volatile suspended solids (TVSS) all in mg/1. A sample volume of 150 ml was used in performing all solids analysis: Tare mass of evaporating dish = 24.3520 g Mass of evaporating dish plus residue after evaporation @ 105 °C = 24.3970g Mass of evaporating dish plus residue after ignition @ 550 °C = 24.3850g Mass of Whatman filter and tare = 1.5103g Mass of Whatman filter and tare after drying @ 105 °C = 1.5439g Residue on Whatman filter and tare after ignition @ 550 °C = 1.5199g
MOITAKIMAKS MUTTGIM 1.) DETERMINE THE COEFFICIENT OF PERMEABILITY FROM THE FOLLOWING DATA (MM/S) LENGHT OF SAMPLE = 25cm ile browsit enitubon Monastale AREA OF CROSS SECTION OF THE SAMPLE = 30 cm² HEAD OF WATER = 40ст to rutemi DISCHARGE = 2.00 mL IN 110 seconds yan! apth inbom utne nit veroo atuato ed basebal 15 olsadneni give in to lua ant of oub nensum step mA'S a pronic, uns gesig te brs
3/7/2021 Water Treatment I-Third class Second semester Q1) The data in the table below used to design a sedimentation tank with depth=4m and detention time= 2hr, the influent flow is 2000L for each minute. 0.01 Settling Velocity(cm/sec) Weight fraction Greater 0.004 0.02 0.03 0.04 0.05 0.063 0.085 0.12 98 95 8 6 4 3 1 0.5 than size % Determine the overall removal efficiency for this tank, s.g. of particle=1.2 , u=0.89x10-³N.s/m². Use Ax=0.1.
The data of an activated sludge process are 3. as follows: MLSS = 5000 mg/lit %3D Flow = 0.15 m3/sec SS of inflow = 400 mg/lit Solids settled after 30 min = 25% %3D Volume of Aeration Tank = 3000m3 %3D Sludge Wastage Rate = 120 m³/day with VSS of 15000 mg/lit. %3D Calculate Sludge Volume Index (SVI), Sludge Density Index (SDI), Return Sludge Ratio (Qp/Q,) and Mean cell residence time (0,).
If 19.3mL of the standardized Na2S203 solution was used in determining the DO, what is the DO concentration of the water sample? 47 O 4.3232mg/L O 35.8208mg/L O 2.0072mg/L O 23.7776mg/L
Water treatment plant : SOR = 0.35 mm/sec; The analysis of this water found that there are 6 different particle sizes: 0.1 mm with settling velocity of 0.2 mm/sec; and percentage of particles = 10 %; 0.2 mm with settling velocity of 0.25 mm/sec; and percentage of particles = 20 %; 0.3 mm with settling velocity of 0.3 mm/sec; and percentage of particles = 15 %; 0.4 mm with settling velocity of 0.35 mm/sec; and percentage of particles = 5 %; 0.5 mm with settling velocity of 0.4 mm/sec; and percentage of particles = 30 %; 0.6 mm with settling velocity of 0.5 mm/sec; and percentage of particles = 20 %; Calculate the efficiency of this tank ?
1.Determine the 5-day BOD (in mg/L) for a 15 ml sample that is diluted with dilution water to a total volume of 300 ml when the initial DO concentration is 8 mg/l and after 5 days, has been reduced to 2 mg/1 2.A 100-ml of water sample has an initial DO level of 2 mg/L, and after 5 days of incubation decreased to 1.8 mg/L. Determine the BDO of the water.
A primary clarifier is to be designed to treat a municipal wastewater. The influent to the clarifier has a flow rate of 7570 m³/d and a total suspended solids concentration of 320 mg/L. A laboratory settling test was performed with the following results: Suspended Solids Concentration (mg/L) at Given Depths Sampling Depth (m) Time (min) 0.61 1.22 246 2.44 272 243 1.83 3.05 10 230 262 282 20 157 195 230 253 30 115 160 211 221 230 45 90 134 163 179 195 60 48 102 131 154 170 90 29 58 86 115 141 (a) Determine the design overflow rate and detention time assuming 65% of the suspended solids are to be removed. Use typical scaling/safety factors as appropriate. (b) Determine the required diameter (to the nearest 0.1 m) and the required depth (to the nearest 0.01 m) for the clarifier.
Q2. A ring infiltrometer (inside area is 962 cm²) test was made on a soil with the results shown in the table below. Elapsed 10 20 30 60 90 150 time (Min) Wat.Vol 300 650 1190 1950 2500 3350 3900 4600 added since start c cubk cenembcr Determine the Horton's Infiltration equation.
A city is planning to install a new settling tank as an upgrade to their existing water treatment plant. Design a settling tank to remove 65% of the influent suspended solids from their design flow of 0.5 m /s. A batch-settling test using a 2.0 m column and coagulated water from their existing plant yielded the following data: Percent removal as a function of time and depth Sampling time, min Depth, m 5 10 20 40 60 90 120 0.5 41 50 60 67 72 73 76 1.0 19 33 45 58 62 70 74 2.0 15 31 38 54 59 63 71
H Gy Q#4:The table shows data of a wastewater sample collected from a river with a temperature of 30 °C analyzed for the BODs test. The rate constant is 0.2 day-¹ at the lab temperature (20 C). Find BODs at the river. Initial dissolved oxygen, mg/L 9 What will be the BOD7 at the river? Final dissolved oxygen, mg/L 3.5 Sample volume, ml 35