1. Calculate the potential due to a dipole as shown in the figure atpositions A and B in millivolts.2. What would be the potential at Bif the distance from the dipole centerto B is doubled,.3. What would be the potential at A if the intensity of the current sourceis doubled.+2mAB=12emF10mm20 degree90 degreer95 cmA.Resistivity = 75 Ohm-cm-2mADipole

“Since you have asked multiple questions, we will solve the first question for you. If you want any…

Answered: 1. Calculate the potential due to a…

Science

Physics

1. Calculate the potential due to a dipole as shown in the figure at positions A and B in millivolts

Inquiry into Physics

8th Edition

ISBN:9781337515863

Author:Ostdiek

Publisher:Ostdiek

Chapter7: Electricity

Section: Chapter Questions

Problem 13P

See similar textbooks

Similar questions

How does the resistance for copper and for silicon change with temperature? Why are the behaviors of these two materials different?
(Indicates a review question, which means it requires only a basic understanding of the material to answer. Questions without this designation typically require integrating or extending the concepts presented thus far.) . Six resistors, all having the same temperatures and compositions, are each attached to a battery with voltage V to form a simple circuit. The resistors have different lengths, l, but the same diameters. Rank the circuits according to the current that flows through the resistor from smallest to greatest. If two (or more) circuits have the same current flowing, give them the same ranking. Explain the rationale you used to establish your rankings. Circuit 1: l = 2 cm; V = 3 V Circuit 2: l = 2 cm; V = 6 V Circuit 3: l = 1 cm; V = 3 V Circuit 4: l = 1 cm; V = 6 V Circuit 5: l = 3cm; V = 2 V Circuit 6: l = 3cm; V = 6 V
Can a wire cany a current and still be neutral—that is, have a total charge of zero? Explain.
In Figure 21.41. does the graph indicate the time constant is shorter for discharging than for charging? Would you expect ionized gas to have low resistance? How would you adjust R to get a longer time between flashes? Would adjusting R affect the discharge time?
Using your understanding of the nature of internal energy and temperature, explain why we might expect the resistance of a solid to increase if its temperature increases.
A defibrillator sends approximately 0.1 C of charge through a patients chest in about 2 ms. The average voltage during the discharge is approximately 3,000 V Compute the average current that flows, the average power output, and the total energy consumed (Note: Only a small portion of this current actually flows through the heart in a typical fibrillating procedure. Much of the charge is diffused throughout the patients thoracic cavity).
A 10-gauge copper wire has a cross-sectional area A=5.26mm2 and carries a current of I=5.00A . The adensity of copper is =89.50g/cm2 . One mole ofcopper atoms (6.021023atoms) has a mass ofapproximately 63.50 g. What is the magnitude of the drift velocity of the elections, assuming that each copper atom contributes one free electron to the current?
Check Your Understanding Handheld calculators often use small solar cells to supply the energy required to complete the calculations needed to complete your next physics exam. The current needed to run your calculator can be as small as 0.30 mA. How long would it take for 1.00 C of charge to flow from the solar cells? Can solar cells be used, instead of batteries, to stall traditional internal combustion engines presently used in most cars and trucks?
What is die basic operation of an ohmmeter as it measures a resistor?
What is the current in milliamperes produced by the solar cells of a pocket calculator through which 4.00 C of charge passes in 4.00 h?
(Indicates a review question, which means it requires only a basic understanding of the material to answer. Questions without this designation typically require integrating or extending the concepts presented thus far.) . A solid metal cylinder has a certain resistance. It is then heated and carefully stretched to form a longer, thinner cylinder. After it cools, will its resistance be the same as, greater than, or less than what it was before? Explain our choice.
Check Your Understanding Copper wires use routinely used for extension cords and house wiring for several reasons. Copper has the highest electrical conductivity rating, and therefore the lowest resistivity rating, of all nonprecious metals. Also important is the tensile strength, where the tensile strength is a measure of the force required to pull an object to the point where it breaks. The tensile strength of a material is the maximumamount of tensile stress it can take before breaking. Copper has a high tensile strength, 2108Nm2 A thirdimportant characteristic is ductility. Ductility is a measure of a material’s ability to be drawn into wires and a measure of the flexibility of the material, and copper has a high ductility. Summarizing, for a conductor to be a suitable candidate for making wire, there are at least three important characteristics: low resistivity, high tensile strength, and high ductility. What other materials are used for wiring and what are the advantages and disadvantages?