1. Calculate the bar force in member AB due to REAL loads in kN.02. Calculate the bar force in member AF due to REAL loads in kN.03. Calculate the bar force in member BF due to REAL loads in kN.04. Calculate the bar force in member CD due to REAL loads in kN.0 PROBLEM 2For the truss shown, members BF, CF, CG,and DG have cross-sectional areas of 750 mm². Allother members have cross-sectional areas of 1,050mm2. The truss is pin supported at A and rollersupported at C. The elastic modulus of all membersis 70 GPa.4.0 mBE75 kN50 kN25 kN3.0 m3.0 m3.0 m3.0 m

Given data in question Loads Dimensions Truss To find out Member forces Note We will use method…

Answered: 1. Calculate the bar force in member AB…

1. Calculate the bar force in member AB due to REAL loads in kN.0 2. Calculate the bar force in member AF due to REAL loads in kN.0 3. Calculate the bar force in member BF due to REAL loads in kN.0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bridge girder AB on a simple span of length L = 30 m supports a distributed load of maximum intensity q at mid-span and minimum intensity q/2 at supports A and B that indudes the weight of the girder (see figure). 450 mm 32 mm B 30 m 16 mm- 1800 mm 32 mm 450 mm The girder is constructed of three plates welded to form the cross section shown. Determine the maximum permissible load q (in kN/m) based upon the following. (a) solely based on an allowable bending stress aallow = 110 MPa kN/m (b) solely based on an allowable shear stress tallow = 50 MPa kN/m (c) accounting for both an allowable bending stress ollow and an allowable shear stress Tallow kN/m
For the truss shown below determine the vertical displacement at joint b. Assume A = 0.15 in², E = 29,000 ksi
A simply supported wood beam that is 13.5 m long carries a 36 kN concentrated load at B. The cross-sectional dimensions of the beam are b- 155 mm, d- 390 mm, a - 65 mm, and c- 30 mm. Section a-a is located at x- 2.3 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. |P H d a В C L 2L 3 Answer: (a) TH - 0.33 kPa (b) TK - i 0.169 kPa (c) Tmax - 0.595 kPa (d) Omax" 27.486 MPa 3
B9
Q2 For the truss shown in the figure:: 4. Determine the force in member fe using the joint method? 5. Determine the force in member bf using section method? 6. Determine the force in member of using section method? g 1 kN 3m 3m Simple Truss I d TTF truss 4 m 3m
A bridge girder AB on a simple span oflength L =14 m supports a distributed load of maximumintensity q at mid-span and minimum intensityq/2 at supports A and B that includes the weight ofthe girder (see figure). The girder is constructed ofthree plates welded to form the cross section shown.Determine the maximum permissible load q basedupon (a) an allowable bending stress σallow =110 MPaand (b) an allowable shear stress τallow = 50 MPa.
What is the maximum absolute shear for the following beam and load group? Use L = 20, a = 3, b = 3, P₁ = 3, P₂ = 3, and P3 = 1. P₁ L P₂ a b P P3
For the truss shown below, applied loads are PB = 73 kN, PC = 36 kN and PD = 15 kN. Using the sign convention 'tension positive', select the correct answer for the axial force in member GH in kN: К F AR G В Рв 4@3m=12m O 1. The axial force in member GH is -60 kN. O2. The axial force in member GH is -78 kN. O 3. The axial force in member GH is -67.1 kN. Н Pc J D Ро K E 4m ?
Calculate the maximum moment (with diagram) & maximum shear (with diagram)
FN-01: ANALYSIS OF FLEXURAL MEMBERS Problem 01: Consider the beam loaded as shown and determine the following. Use Pn 10 x Class number + 50 kN. 1. The maximum bending moment 2. The maximum Shear 3. Maximum Deflection 4. Determine the bending coefficient. Show complete and orderly solution. w=5kN/m 1.50m 2Pn x marks are the location of lateral bracings 5.0m 3.0m
Rigid beam AB is supported by three bolts at A and a pin at B. The bolts at A are in double shear and have a diameter of 0.250 in. Assume L= 4.0 ft. If the average shear stress in the bolts cannot exceed 70 ksi, determine the maximum distributed load wmax that can be supported by the structure. (1) A Answer: Wmax IN L B kips/ft
2. A simple steel beam is to carry the concentrated loads as shown in the figure. (a) Drav the shear diagram, (b) determine the maximum moment, and (c) determine the wide-flange shape that should be used from the list shown if the allowable normal stress for the grade of steel to be used is 110 MPa 60 KN/m 60 KN/m A B 4 m 1m2 m Shape W310x129 S (cm') 1955 Shape W310x202 S (cm) 5049 3423 W310x143 2155 W310x226 W310x158 2565 W310x253 3853 W310x179 2675 W510x285 4311