1. Analyze the statically indeterminate beam by displacement method, and draw thebending moment diagram, assume that El is constant.80kN2m2m4m2. Analyze the statically indeterminate rigid frame by displacement method, and drawthe bending moment diagram, assume that El is constant.15kN/m114m4m

Since you have asked multiple questions, we will solve the first question for you. If you want any…

Answered: 1. Analyze the statically indeterminate…

1. Analyze the statically indeterminate beam by displacement method, and draw the bending moment diagram, assume that El is constant. 80kN 2 93 2m 2m 4m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The boom AC in the figure rests in a ball and socket joint at A and is held in equilibrium by the…

A: To find: Coordinates of D

Q: Determine the maximum displacement of the beam. Use the moment-area theorems. Take E = 29(10^3) ksi,…

Q: Determine the deflection at C and the slope of the beam at A, B and C using Area-Moment Method. El…

Q: 4. DETERMINE THE MOMENT OF THE FORCE F AT THE END OF THE ANGLE BRACKET ABOUT POINT O. THE VALUE OF F…

Q: Determine the equations of the elastic curve for the beam using the x coordinate. Specify the slope…

A: The FBD of the given beam is shown below: Since both the support carry a concentrated moment the…

Q: Solve the following using moment-area method. Draw the moment diagrams by part

Q: Since the bending stiffness of the AB section is 2EI and the bending stiffness of the BC section is…

A: Question is based on overhang beam subjected to uniform load at half of the span. Collapse and…

Q: I point A of the beam show

A: here we have to find out deflection and slope at point A

Q: Problem: Determine the deflection specified in each of the following beams. Assume constant El. Use…

A: Given data: Modulus of elasticity, E=200 GPa Moment of inertia, I=800×106 mm4 The given beam is…

Q: 1. Determine the Moment due to force F about: a. Point O b. Point B Note: The thickness of the beam…

A: To Determine The Moment due to force F about: a. Point O b. Point B

Q: use the method of virtual work and determine the vertical deflection at the rocker support D. EI is…

A: Given, EI constant to find vertical deflection at D, using the virtual work principle. The virtual…

Q: If the force F = 100 N lies in the plane DBEC, which is parallel to the x–z plane, and makes an…

A: Lets first find out position vectors for points A and B,

Q: DETERMINE THE VERTICAL DISPLACEMENT OF JOINT A. EACH BAR IS MADE OF STEEL AND HAS A CROSS SECTIONAL…

Q: Problem 7: The beam below is subjected the loading as shown. Use the Moment-Area method to determine…

A: An overhanging beam with uniformly distributed load and point load.A is roller support, B is hinged…

Q: 3. A beam is loaded as shown. El is constant. The vertical reactions at B and C are equal to 80KN.…

A: ###Determination of Macaulay Method###

Q: Q#5. Determine the displacement at point C and slope at point B of the steel beam shown. El is…

Q: fixed in the middle motor 2. A rotating of the weighting 3 ton (mass) is 52,36 jad/sec two simple…

Q: 4) The truss is made of steel (a = 12.0(10/*C) and is loaded and supported as shown. You may assume…

Q: Determine the position a of roller support B in terms of L so that deflection at end C is the same…

Q: The angles between two forces to make their resultant a minimum and maximum respectively are: O and…

Q: Problem 2 B a A d The 54-N force P is applied perpendicular to the portion BC. Given a = 35.1 deg…

Q: n the omage below Ties on the ground e supports the load Shown. Assuming the upward reaction of the…

Q: 2. determine the deflection at midspan. con- sider El as constant and start x from A. A 10kN/m W B√√…

A: Given Data EI = Constant Find mid span deflection.

Q: A beam is subjected to concentrated force as shown in the figure below. The EI of the entire beam…

A: A propped cantilever beam of span 15 ft, propped at C and fixed at A. A point load of 36 kips is…

Q: 1. A beam ABCD is hinge supported at A, B, and C. AB = BC = CD = 7m. The support B and C sink 6mm…

A: Data given Beam = ABCD Support condition = Hinge at A, B and C Distance between two consecutive…

Q: A truss bridge has a concentrated load as shown below. As an Engineer use the principle of virtual…

Q: 4. A force of 540N is directed from C towards E in the cube. a. Determine the moment about the…

A: Given a force of 540N is directed from C towards E. It is required to determine the moments about x,…

Q: "| w=wo (1-) B A

Q: theta = 33 degrees M1 = 450 Nm M2 = 550 Nm M3 = 650 Nm a. Find the x-component of the resultant…

Q: Use conjugate beam method to solve the rotation at A and B and the displacement at C and D. EI is…

A: Use conjugate beam method to solve the rotation at A and B and the displacement at C and D. EI is…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

1. Analyze the statically indeterminate beam by displacement method, and draw the
bending moment diagram, assume that El is constant.
80kN
2m
2m
4m
2. Analyze the statically indeterminate rigid frame by displacement method, and draw
the bending moment diagram, assume that El is constant.
15kN/m
11
4m
4m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2 Interpretation of data

VIEW

Step 3 Primary calculations

VIEW

Step 4 Calculations for distribution factor

VIEW

Step 5 Moment distribution table

VIEW

Step 6 Bending moment diagram

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The equilibrium equations used in method of section for finding the forces in the members of a truss is given as a. EV = 0 Ο b. ΣM - 0 C. ΣΗ0 d. ΣV - 0 and ΣΗ =0
Determine the slope and displacement at point B. Assume the support at A is a pin and C is a roller. Account for the additional strain energy due to shear. Take E = 29(103) ksi, I = 300 in4, G = 12(103) ksi, and assume AB has a cross-sectional area of A = 7.50 in2. Use the method of virtual work.
Problem 2. Use Force Method A) For the frame shown below, draw the shear and moment diagram B) Find the horizontal deflection at Cusing virtual work Assume El is constant. C 30 ft 10 ft 15 kips 10 ft
helpppp
The El of the beam is constant. Virtual forces. 8) Using an energy method (strain energy, virtual forces, or Castigliano's Theorem-your choice!), find the displacement at the free end of beam ABC. For the beam, EI is constant. L B b P dc=
Using the virtual work method determine slope of the beam at "A". Beam is subjected to a uniformly Distributed Load “W" and a concentrated moment "WL^2" at “A" (Express the results in terms of W, L, and EI) w ikIft=constant)
Solve the problem by the moment-area method. The beam has constant flexural rigidity EI. A simple beam AB supports two concentrated loads P at the positions shown in the figure. B C 4. 4 A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d = 12 mm, L = 5.4 m, E = 200 GPa, and I = 193 x 10° mm, calculate the magnitude of the loads P (in kN) so that the beam just touches the support at C. 163.87 x kN
Find the maximum angle of rotation for the shaft subjected to linearly %3D distributed torque. Tx) = kx,GJ constant. T(x)
Apply Principles of Symmetry and determine the displacement of joint C. Assume B, C, and D are fixed. Assume A, E and I are constant for all the members.
Use moment area method.
Use double integration method
Determine the equation of the elastic curve, the slope at A, and the deflection at B. EI is constant.