1. Air enters a nozzle steadily at 2.21 kg/m3 and 30 m/s and leaves at 0.762 kg/m3 and 180 m/s. If the inlet area of the nozzle is 80 cm2, determine (a) the mass flow rate through the nozzle, and (b) the exit area of the nozzle.

1. Air enters a nozzle steadily at 2.21 kg/m3 and 30 m/s and leaves at 0.762 kg/m3 and 180 m/s. If the inlet area of the nozzle is 80 cm2, determine (a) the mass flow rate through the nozzle, and (b) the exit area of the nozzle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6 m/s air at atmospheric conditions of 20°C and 1 bar (100 kPa) and consumes 300 kW electric power when operating. Air is compressed to a gage pressure of 8 bar (absolute pressure of 900 kPa), and compressed air is transported to the production area through a 30-cm- internal-diameter, 83-m-long, galvanized steel pipe with a surface roughness of 0.15 mm. The average temperature of compressed air in the pipe is 60°C. The compressed air line has 8 elbows with a loss coefficient of 0.6 each. If the compressor efficiency is 76 percent, determine the power wasted in the transportation line. The roughness of a galvanized steel pipe is given to be ɛ = 0.00015 m. The dynamic viscosity of air at 60°C is u= 2.008 x 10° kg/m-s, and it is independent of pressure. The density of air listed in that table is for 1 atm. The density at 20°C, 100 kPa and 60°C, 900 kPa can be determined from the ideal gas…
Air at temperature 26 °C and pressure 101.4 kPa enters the diffuser steadily with a velocity of 190 m/s. The inlet area of the diffuser is 0.6m2. The air leaves the diffuser with nearly zero velocity. Determine the mass flow rate in kg/s of the air. Use R=0.287 kJ/kgK. Please keep one decimal for the final answer.
Water vapor enters a nozzle at 400 °C and 800 kPa, with a speed of 10 m/s, and leaves at 375 °C and400 kPa, while losing heat at a rate of 25 kW. For an entrance area of 800 cm?, determine thevelocity and area of the water vapor at the nozzle outlet in m/s, and cm?, respectively.
In a steady flow apparatus, 135 kJ of work is done on each kg of fluid. The specific volume of the fluid, pressure, and speed at the inlet are 0.37 m /kg, 600 kPag, and 160 m/s. The inlet is 32 m below the floor, and the discharge pipe is at floor level. The discharge conditions are 0.62 m /kg, 100kPag, and 27 m/s. The total heat gained between the inlet and discharge is 9 kJ/kg of fluid. In flowing through this apparatus, by how much does the specific internal energy increase or decrease? O 290.8 (increase) 2.79 (increase) O 2.79 (decrease) O20.79 (increase) Next Previour
Argon (100 kPa and 10 deg C) enters a compressor with a mass flowrate of 0.19 kg/s. It exits at 600 kPa and 130 deg C. The compressor has a specific heat loss of 16 kJ/kg. What is the power (kW) required for the compressor? Report your answer to 2 decimal places.
A garden hose attached with a nozzle is used to fill a 22-gal bucket. The inner diameter of the hose is 1 in and it reduces to 0.5 in at the nozzle exit. If the average velocity in the hose is 7 ft/s, determine (a) the volume and mass flow rates of water through the hose, (b) how long it will take to fill the bucket with water, and (c) the average velocity of water at the nozzle exit.
A pump increases the water pressure from 8 kPa at the inlet to 700 kPa at the outlet. Water enters this pump at 41.51°C through a 1.774-cm-diameter opening and exits through a 2.327-cm-diameter opening. Determine the velocity of the water at the outlet in m/s when the mass flow rate through the pump is 1.163 kg/s. The specific volume of incoming water is 1.303 x 10³ m³/kg.
A 5 KW pump is used to raise the elevation of a lake's water by 25 m from the free surface of the lake. The pipe inlet is 2 m below the free surface. The temperature of water increases by 0.05oC during the process as a result of the frictional effects. Neglecting any heat transfer and kinetic energy changes, determine the mass flow rate of the water.
A pump increases the water pressure from 8 kPa at the inlet to 700 kPa at the outlet. water enters this pump at 41.51 degree celcius through a 1.15-cm diameter opening. Determine the velocity of the water at the outlet in m/s when the mass flow rate through the pump is 2.637 kg/s the specific volume of incoming water is 1.799 x 10-3 m3/kg.
Q8. A gas enter a turbine with a velocity of 300 m/s and a temperature of 527 °C and specific internal energy of 688 kJ/kg and density of 2.7 kg/m³ . The gas expand adiabatically from a pressure of 620 kN/m² to 130 kN/m² .The gas leaves the turbine with velocity of 150 m/s. Determine the power output from the turbine in kilowatt. Take the mass flow rate of 4 kg/s. 00 limite through ongine Qvel 300 °C ond 50 9C tho hoot roiootod tompooretur
1) Air with a density of 0.45 kg/m3 enters an experimental jet engine at a rate of 175 m/s. The inlet area of the engine is 7.0 ft2. After fuel is burned, the air and combustion byproducts leave the engine with a velocity of 695 m/s through an outlet area of 6.0 ft2. What is the average density of the gas exiting the engine? Express your answer in kg/m3, slugs/ft3, and lbm/ft3. 2) Calculate the mass moment of inertia of the thin ring shown in the accompanying diagram. Express your answer in lbm · ft2, lbm · in2, and slugs · ft2. (Assume the axis of rotation is into the page through the center of the ring.) m = 0.8 slugs radius is 9 in.